[arm-allstar] New install V1.7-01

[Dan Jernheden]

I can add this information from the menu.

I) Toggle PTT mode (currently active LOW)
J) Change COSFORM Mode (currently "usb")
L) Change CTCSSFROM Mode (currently "usb")

Also (keyed status) from telemetry display when node idle..?

REALTIME RX TELEMETRY DISPLAY:
        COS        |    COS    |    COS      |   CTCSS   | CTCSS     |  PTT
(composite) |  (input) |   (test)     |  (input)  | (override)  |
      KEYED      |  KEYED  |   CLEAR  |   KEYED   |   CLEAR      | CLEAR

Dan/SM6TZL

Den 2023-12-04 kl. 11:03, skrev Dan Jernheden:
> All DTMF tones from RF decodes and prints in the Asterisk CLI.
> But I get no response on RF (the node is not even keying up) when 
> sending eg. *70. I am expecting system status on RF with the *70 command.
>
> Still the PTT works. I can hear some hourly identification on RF.
>
> My /etc/asterisk/rpt.conf settings are:
> duplex=1
> telemetry=telemetry58973
> telemdefault=2
>
> Dan/SM6TZL
>
>
> Den 2023-12-04 kl. 02:24, skrev Dave Petrie:
>> are you sending the tones via RF or on suppermon
>>
>> if only dtmf try supermon and if both fail then like Rich said check 
>> to make sure
>> telemetry is enabled in rpt.conf
>> you can also log into putty menu 9 and do  asterisk -rvvv
>> and watch to see if all your dtmf tones are being decoded
>> i had to add this line in simpleusb.conf to get all my RF dtmf tones 
>> to work
>>
>> dtmf_relax=1 ;when dtmf tones are not decoding this opens the door wider
>> Sent from my iPhone
>>
>>> On Dec 3, 2023, at 1:18 PM, Dan Jernheden via ARM-allstar 
>>> <arm-allstar at hamvoip.org> wrote:
>>>
>>> Hello everyone!
>>>
>>> I recently installed HamVoIP: RPi-Z2W-2-3-4_V1.7-01_Allstar on 
>>> RaspberryPi 2B.
>>>
>>> I’ve gone through the configuration menu and PTT, COS and audio 
>>> levels looks ok. The DTMF decoder seems to work also from CLI client 
>>> output.
>>> But I got no response from Allstar when sending DTMF-commands...? If 
>>> I do *70 nothing happens... I was expecting a system status report.
>>> What am I missing?
>>>
>>> This is the output from log:
>>> [root at AllStar ~]# cat /var/log/asterisk/messages
>>> [Dec  3 18:11:25] NOTICE[312] dnsmgr.c: Managed DNS entries will be 
>>> refreshed every 300 seconds.
>>> [Dec  3 18:11:25] NOTICE[312] cdr.c: CDR simple logging enabled.
>>> [Dec  3 18:11:25] NOTICE[312] loader.c: 117 modules will be loaded.
>>> [Dec  3 18:11:25] NOTICE[312] chan_irlp.c: Unable to load config 
>>> irlp.conf
>>> [Dec  3 18:11:25] WARNING[312] cdr_odbc.c: cdr_odbc: Unable to load 
>>> config for ODBC CDR's: cdr_odbc.conf
>>> [Dec  3 18:11:25] NOTICE[312] chan_usbradio.c: Unable to load config 
>>> usbradio.conf
>>> [Dec  3 18:11:25] ERROR[312] chan_echolink.c: Unable to load config 
>>> echolink.conf
>>> [Dec  3 18:11:26] NOTICE[312] pbx_ael.c: Starting AEL load process.
>>> [Dec  3 18:11:26] NOTICE[312] pbx_ael.c: AEL load process: 
>>> calculated config file name 
>>> '/usr/local/hamvoip-asterisk/etc/asterisk/extensions.ael'.
>>> [Dec  3 18:11:26] NOTICE[312] pbx_ael.c: File 
>>> /usr/local/hamvoip-asterisk/etc/asterisk/extensions.ael not found; 
>>> AEL declining load
>>> [Dec  3 18:11:26] ERROR[312] chan_voter.c: Unable to load config 
>>> voter.conf
>>> [Dec  3 18:11:26] WARNING[312] pbx_spool.c: Unable to create queue 
>>> directory /var/spool/asterisk/outgoing -- outgoing spool disabled
>>> [Dec  3 18:11:26] ERROR[312] codec_dahdi.c: Failed to open 
>>> /dev/dahdi/transcode: No such file or directory
>>> [Dec  3 18:11:26] NOTICE[322] app_rpt.c: Normal Repeater Init 58973
>>> [Dec  3 18:11:26] NOTICE[322] app_rpt.c: Normal Repeater Init 1999
>>> [Dec  3 18:11:26] NOTICE[325] chan_iax2.c: Registered IAX2 to 
>>> '162.248.92.131', who sees us as xx.xxx.xxx.xxx:4569 with no 
>>> messages waiting
>>>
>>> [Dec  3 18:11:26] NOTICE[359] chan_simpleusb.c: Loaded parameters 
>>> from simpleusb_tune_usb.conf for device usb .
>>> [Dec  3 18:16:42] WARNING[389] file.c: File /tmp/ip does not exist 
>>> in any format
>>> [Dec  3 18:16:42] WARNING[389] file.c: Unable to open /tmp/ip 
>>> (format 0x4 (ulaw)): No such file or directory
>>> [Dec  3 18:16:42] WARNING[389] app_rpt.c: ast_streamfile failed on 
>>> DAHDI/pseudo-2009024883
>>>
>>> Do I need to fix some of this for normal AllStar simplex node 
>>> operation?
>>>
>>> Dan/SM6TZL
>>>
>>> _______________________________________________
>>>
>>> ARM-allstar mailing list
>>> ARM-allstar at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>
>>> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org