[arm-allstar] FW: HF control

[Doug Crompton]

Les,

  I am still not clear on this? You are using two different nodes a both
ends - one for TX audio and one for RX audio? If that is the case and you
want the node sending HF audio TO you to be keyed all the time you can tie
the COS at that end low with cos set to usbinvert or high (open) with cos
set to usb.  I mentioned this before. Why is that a problem to do?


*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*


On Fri, Mar 6, 2020 at 1:20 AM "Les bradshaw via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> I am Transmitting on the HF rig it  works well. The problem is having to go
> to node (2) to toggle the (K) so I can get receive audio from the HF rig on
> Node (1). If node (2) was to reboot and I was not there then that would be
> a problem.
>
> On Wed, Mar 4, 2020 at 2:57 PM "Doug Crompton via ARM-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > Les,
> >
> >  Do you need to toggle the keying? Is this just monitor mode or are you
> > also Transmitting audio on HF?
> >
> >
> > *73 Doug*
> >
> > *WA3DSP*
> >
> > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> >
> > On Wed, Mar 4, 2020 at 3:53 PM "Les Bradshaw via ARM-allstar" <
> > arm-allstar at hamvoip.org> wrote:
> >
> > > Doug ,
> > >         Please see info below, I have another question is it possible
> > > after connecting node (1) to node (2) to be able to send a DTMF tone
> from
> > > node (1) to node (2) that will toggle the simpleusb (K) (COS Keyed )
> > > command ?
> > > Thanks,
> > > Les
> > > N5LMB
> > >
> > > Sent from Mail for Windows 10
> > >
> > > From: Les Bradshaw
> > > Sent: Wednesday, March 4, 2020 9:46 AM
> > > To: arm-allstar at hamvoip.org
> > > Subject: Re: [arm-allstar] HF control
> > >
> > > I am working on setting up two nodes so I can connect to my HF rig
> > Remote,
> > > node (1) is radio-less set at duplex=0. Node (2) HF Node is set
> duplex=0,
> > > All works well after I boot them up and connect Node (1) to Node (2)
> > then I
> > > have to go to simpleusb on Node(2) and set setting (K) to Keyed to get
> > > audio from the HF Node (2) to Radio-less node (1)  then all works well
> > then
> > > have to key Node(1) to reset time when audio drops out witch is no
> > problem.
> > > My Question is how can I set Node (2) HF node to COS Keyed after I
> > connect
> > > to it without having to go to simpleusb or is there a better way to set
> > > this up ?
> > > Thanks,
> > > Les
> > > N5LMB
> > >
> > >
> > > Sent from Mail for Windows 10
> > >
> > >
> > > _______________________________________________
> > >
> > > ARM-allstar mailing list
> > > ARM-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> >
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>