[arm-allstar] No Audio in...

[Cesar Gonzalo]

Its moving when I press the ptt on the radio
So I guess audio is going.
Ptt is not problem , if I use the Cli, I get back the time and everithing
.

But if I try it using a radio to the node , i dont have anything back

On Fri, Feb 7, 2020, 17:54 Doug Crompton <wa3dsp at gmail.com> wrote:

> Cesar,
>
>  Using the main menu select simpleusb tune menu and you will see as
> below....
>
> Select item J to change to or from usb/usbinvert
>
> Select item K to key COS.  Then item 2 you should see audio on the
> bargraph display and set the level. It should go to 5Khz on peaks.. You can
> use K to manually key/unkey instead of the vox.
>
> Active simpleusb device stanza: [usb] ------------------------------------
> S) Select active USB device stanza
> V) View COS, CTCSS and PTT Telemetry using real-time display
> P) Print Current Parameter Values ---- 2) Set Rx Voice Level (using
> display)
> 3) Set Transmit A Level           ---- 4) Set Transmit B Level
> 5) Set Tx Audio Level Method (currently LOG)
> 7) Set Transmit DSP Level
> B) Toggle RX Boost Mode (currently Enabled)
> C) Toggle Echo Mode (currently Disabled)
> D) Flash (Toggle PTT and Tone output several times)
> E) Toggle Transmit Test Tone/Keying (currently Disabled)
> K) Manually key COS (currently Unkeyed)
> F) Toggle PRE-emphasis Mode (currently Disabled)
> G) Toggle DE-emphasis Mode (currently Disabled)
> H) Toggle PLfilter Mode (currently Disabled)
> Q) Toggle DCSfilter Mode (currently Enabled)
> I) Toggle PTT Mode (currently active LOW)
> J) Change COSFROM Mode (currently "usb")
> L) Change CTCSSFROM Mode (currently "no")
> M) Change RXONDELAY value (currently "0")
> N) Change RXAUDIODELAY value (currently "0")
> W) Write (Save) Current Parameter Values
> 0) Exit Menu
>
> Please enter your selection now:
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>
> On Fri, Feb 7, 2020 at 4:54 PM Cesar Gonzalo <cesgonm at gmail.com> wrote:
>
>> I know Vox is not a good idea , but for now , it is good enough to make
>> it easy.
>>
>> I did changed to usbinvert but still have the same issue, no response
>> when sendin *81 from other radio.
>>  Where I'm supposed to change to low or High
>>
>> On Fri, Feb 7, 2020, 15:13 "Doug Crompton via ARM-allstar" <
>> arm-allstar at hamvoip.org> wrote:
>>
>>> Just to be clear - I think I said simpleusb.conf - I meant simpleusb tune
>>> menu from the main hamvoip menu.
>>>
>>>
>>> *73 Doug*
>>>
>>> *WA3DSP*
>>>
>>> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>>>
>>> On Fri, Feb 7, 2020 at 12:42 PM "Cesar Gonzalo via ARM-allstar" <
>>> arm-allstar at hamvoip.org> wrote:
>>>
>>> > Hi to all , hope I can get some help with my node.
>>> >
>>> > First what I have :
>>> > Raspberry Pi 4
>>> > Usb fob cm-108 Unmodified
>>> > Easy digi Vox
>>> > Uv-5
>>> >
>>> > Trying to use vox , and it is working, but I can not get the audio in
>>> >
>>> > I can see the rx visual moving when I key , and when i send tones ,
>>> but not
>>> > answer back .
>>> >
>>> > Using CLI: Rpt fun 51024 *80 or others i get audio back.
>>> >
>>> > At the beginning it was giving me node xxxxx time out
>>> >
>>> > I changed the last cts.. to PP, and not giving me the time out any
>>> more.
>>> >
>>> > When reboot node , it give me ip address and ibsee the status green
>>> >
>>> > Problem
>>> >
>>> > When trying to send a tone *80 , seems that it is not recognized
>>> nothing
>>> > happend no reply
>>> >
>>> > I tried Parrot 1 , nothing too.
>>> >
>>> > I guess audio is not going trough,  even i I see it on the visual.
>>> >
>>> > Any help please.
>>> >
>>> > Thanks
>>> >
>>> > 73
>>> > _______________________________________________
>>> >
>>> > ARM-allstar mailing list
>>> > ARM-allstar at hamvoip.org
>>> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>> >
>>> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>>> >
>>> _______________________________________________
>>>
>>> ARM-allstar mailing list
>>> ARM-allstar at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>
>>> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>>>
>>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 20200207_184350.jpg
Type: image/jpeg
Size: 2837431 bytes
Desc: not available
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20200207/9d0eabd6/attachment-0001.jpg>