[arm-allstar] eth0 & wlan0

[Bryan St Clair]

I am not sure running both at the same time is a great idea.

If you reboot the node, with the ethernet cable disconnected, does your SSH
connection work on Wifi?

Bryan

On Wed, Dec 16, 2020 at 1:50 PM "Peter Paul Fox via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> Hi all,
>
> I have an odd problem which has appeared. When I have the ethernet cable
> plugged into the RPi I can SSH into it using either the eth0 IP or the
> wlan0 IP value (both different) When I remove the ethernet cable I cannot
> SSH into wlan0
> I put the cable back in and SSH into Allstar. And at the top of the menu
> it says;
> Admin Menu List for RPI  (192.168.xx.29, 192.168.xx.22) and restarted the
> Asterick Server I get
> Automatically restarting Asterisk          Restart Asterisk Server
>   ended with exit status 1
> Asterisk died with code1.
>
> Using Supermon I try to connect to a local Node but it attempts and quits
> without any message.
>
> Running CLI I get
>
> WARNING[26810]: chan_iax2.c:7844 registry_rerequest: Received unsolicited
> registry authenticate request from '192.83.199.4'
>
> When I run ifconfig I get this and I notice ‘Ethernet’ is in both eth0 and
> wlan0
> 192.168.xx.255 is not my gateway.
>
> eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
>         inet 192.168.xx.29  netmask 255.255.255.0  broadcast 192.168.xx.255
>         ether b8:27:eb:c0:20:1e  txqueuelen 1000  (Ethernet)
>         RX packets 5919616  bytes 301440965 (287.4 MiB)
>         RX errors 0  dropped 2851  overruns 0  frame 0
>         TX packets 645355  bytes 59791574 (57.0 MiB)
>         TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
>
> lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
>         inet 127.0.0.1  netmask 255.0.0.0
>         loop  txqueuelen 1000  (Local Loopback)
>         RX packets 1190591  bytes 95612400 (91.1 MiB)
>         RX errors 0  dropped 0  overruns 0  frame 0
>         TX packets 1190591  bytes 95612400 (91.1 MiB)
>         TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
>
> wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
>         inet 192.168.xx.22  netmask 255.255.255.0  broadcast 192.168.xx.255
>         ether 00:36:00:00:f7:d2  txqueuelen 1000  (Ethernet)
>         RX packets 6391903  bytes 431486329 (411.4 MiB)
>         RX errors 0  dropped 361674  overruns 0  frame 0
>         TX packets 18637  bytes 1161330 (1.1 MiB)
>         TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
>
> There must be an error in a config file but my knowledge of Linux works if
> I can do the correct search, but not managed to find the route. I know I
> can rebuild from scratch easily but sometimes I like to find the problem in
> case it occurs again.
>
> Peter Paul Fox G8HAV
> 5 Llandovery Close
> WINSFORD CW7 1NA
> Tel: +447919315547
>
> Dane Valley RAYNET
> Midcars.org
>
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>


-- 
Bryan
K6CBR
bryan at k6cbr.us
43918,439910