[arm-allstar] File Not Playing Globally

[Kyle Krieg]

Yes, that's what we are going to do since 40105 and 1085 are linked full
time.

Thanks for the quick response and info.  Always learning something new
about AllStar.  So far it's been great!

Kyle


On Sun, Sep 29, 2019 at 6:00 PM David McGough <kb4fxc at inttek.net> wrote:

>
> Kyle,
>
> Sounds good.  Another simple work-around would be to run the playback from
> node 40105. Then, node 1085 could remain duplex=0.
>
> 73, David KB4FXC
>
>
> On Sun, 29 Sep 2019, Kyle Krieg wrote:
>
> > Got it.
> >
> > Node 1085 is set to duplex = 0
> >
> > Node 40105 is set to duplex = 1
> >
> > The reason why we set node 1085 to duplex = 0 is because it's connected
> to
> > a CAT800 on port 2, as it was suggested in the rpt.conf file to set it to
> > duplex=0.
> >
> > Anyway we can set node 1085 to duplex=1 but have it connected full time
> to
> > a CAT800 repeater controller.  If not, we have a work around, which isn't
> > that big deal.  Just was making sure I wasn't doing something wrong.
> >
> > Kyle
> >
> >
> >
> >
> >
> > On Fri, Sep 27, 2019 at 5:13 AM David McGough <kb4fxc at inttek.net> wrote:
> >
> > >
> > > Kyle,
> > >
> > > What are the rpt.conf duplex settings on these nodes?? I'm guessing
> > > node 1085 and/or 40105 are set duplex=0.
> > >
> > > To propagate a playback message, the originating and all relaying nodes
> > > must not be set duplex=0.  The final endpoints can be duplex=0.
> > >
> > > So, for example, doing a playback from node 1085:
> > >
> > > 1085  (not duplex=0)
> > >  |
> > >  |
> > >  V
> > > 40105 (not duplex=0)
> > >  |
> > >  |
> > >  V
> > > 48370 (duplex=0 okay)
> > >
> > >
> > > 73, David KB4FXC
> > >
> > >
> > > On Thu, 26 Sep 2019, "Kyle Krieg via ARM-allstar" wrote:
> > >
> > > > I have this line in a script I call via DTMF.
> > > >
> > > > /usr/bin/asterisk -rx "rpt playback 1085 /tmp/newsline/newsline"
> > > >
> > > > When executing this script from node 1085, the newsline file plays
> > > locally
> > > > on 1085, but does not play on any other nodes connected.  I was
> under the
> > > > assumption "playback" was for global playback and localplay was for
> only
> > > > playing locally?  Is there an attribute I'm missing?
> > > >
> > > > There are two other nodes connected, three nodes total.  All are
> > > connected
> > > > via transceive.
> > > >
> > > > Here is the bubble chart of who's all connected.
> > > >
> > > > http://stats.allstarlink.org/getstatus.cgi?48370
> > > >
> > > > Thanks
> > > > Kyle
> > > > _______________________________________________
> > > >
> > > > ARM-allstar mailing list
> > > > ARM-allstar at hamvoip.org
> > > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > > >
> > > > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > > >
> > >
> > >
> >
>
>