[arm-allstar] RPi3 TX/RX issues

[Doug Crompton]

Josh,

 We don't do anything in the Allstar code with the built-in audio. We use
USB FOBS for Allstar audio. So I am not sure what you are referring to.
What is it you want to do with the internal audio? It is usually directed
to the HDMI port by default but we do not use it. Remember this is
Archlinux. You can confirm if the problem is from Asterisk/Allstar by
booting without it. Comment the call in /etc/rc.local.



*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*

On Sun, Jan 1, 2017 at 6:05 PM, "Josh W4ZZK via arm-allstar" <
arm-allstar at hamvoip.org> wrote:

> I'm sure that I am having a hw "priority" issue with my RPi3.
>
> I believe that the RPi3 is using the integrated audio chip (1/8" jack
> and/or HDMI audio stream) and I need to do some configuring in "alsa-base"
> to disable the integrated hardware.
>
> On another note, I reflashed the SD Card with a fresh copy of the HamVOIP
> beta for RPi 3, configured it for "my" station, it worked fine! Finally....
> then after shutting down to relocate from my easy-chair to my shack, it's
> back at square one (as far as the sound priorities go).
>
> Must be something how it logically loads scripts and perhaps this Alsa-Base
> script is the place to start?
>
> Thoughts? Happy New Year to all!
> Josh Hatton W4ZZK
>
> On Thu, Dec 29, 2016 at 12:05 PM, Lawrence Roney <roney at chiarappa.com>
> wrote:
> > Hello,
> >
> > In /etc/asterisk/simpleusb.conf file
> >
> > If you are running a simplex, single radio node, make sure duplex=0.  If
> running a 2 radio repeater setup, then duplex=1.
> >
> > Then, depending on where you tapped the receive and transmit audio, you
> may need to uncomment (remove the ";") on the following lines:
> >
> > ;deemphasis=yes     ; enable de-emphasis (input from discriminator)
> > ;preemphasis=yes    ; enable pre-emphasis (output to TX)
> >
> > See if that helps.
> >
> > Thanks,
> >
> > Lawrence - N6YFN
> >
> >
> > -----Original Message-----
> > From: arm-allstar [mailto:arm-allstar-bounces at hamvoip.org] On Behalf Of
> "Josh W4ZZK via arm-allstar"
> > Sent: Thursday, December 29, 2016 9:53 AM
> > To: arm-allstar at hamvoip.org
> > Cc: Josh W4ZZK <w4zzkjosh at gmail.com>
> > Subject: [arm-allstar] RPi3 TX/RX issues
> >
> > Good Morning All,
> > Rather new to the RPi world, but eager to dig deeper and get an optimized
> Allstar system running.
> >
> > Running Arch Linux 4.1.19-5
> >
> > I am having an issue with responses to DTMF commands. Using
> SimpleUSB-Tune-Menu, my USB Fob (a RALI 3 Module) has good RX signal,
> transmits good 1K Pulse Tones... all the standard stuff seems to
> pass....... However, "Echo" does not function, and all commands received
> thru the Radio via DTMF will not "play" or transmit until I unplug the USB
> Fob, then connect it again.
> >
> > Any ideas? Please ask questions to get a more clear picture, if you need
> to.
> >
> > Thanks much.
> > Josh  W4ZZK
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
> > Scanned by Symantec Email Security.cloud service.
> >
> >
> >
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>
>