[arm-allstar] More on Zoiper on the iphone

[David McGough]

Hi Dave,

Hum...I don't know and don't have an iPhone to test with.

If you can get to the actual XML configuration file, the manual suggests 
there are level settings.  See the "audio" section of this document:

http://www.zoiper.com/documentation/Zoiper_3_Configuration_File.pdf

I have no idea if any of this info will help---just shooting in the dark!

73, David KB4FXC



On Sat, 10 Sep 2016, Dave Miller via arm-allstar wrote:

> Dave,
> I can't seem to find these setting you are talking about in Zoiper for
> iPhone?
> I would love to boost audio as well.
> The settings tab under Audio has 5 items
> Echo cancellation             set to software
> Automatic Gain Control    set to software
> 3 on off toggles
> Noise suppression software
> Dialpad sounds
> Ring while talking.
> 
> Where is "Zoiper->Config->Audio" on a iphone.
> 
> Thanks
> Dave
> VE7HR
> 
> 
> On Sat, Sep 10, 2016 at 2:11 PM, David McGough via arm-allstar <
> arm-allstar at hamvoip.org> wrote:
> 
> >
> > Hi Tom,
> >
> > Glad it's working.
> >
> > Since the volume level issue is with Zopier directly, Zopier would ideally
> > be the best place for a wider range volume adjustment method, rather than
> > Asterisk, in this scenario.
> >
> > For my curiosity, I just google'd some phrases similar to: "zopier low
> > volume" and low volume levels seem to be common complaints. Some comments
> > mention looking through the Zopier settings, such as:
> >
> > ..."There is a speaker gain option in Zoiper->Config->Audio, which you can
> > try. Another option in the same menu is the "Audio Driver". Speaker gain
> > should do the trick, but try both, do some tests with them to see which
> > will have better effect with your device."...
> >
> > 73, David KB4FXC
> >
> >
> >
> > On Sat, 10 Sep 2016, Tom Whiteside via arm-allstar wrote:
> >
> > > I was able to finally get Zoiper to properly register with my Allstar
> > node -
> > > the final piece of the puzzle was to change the iax.conf "host=" line to
> > > dynamic as the example code had to start with.   Got confused thinking
> > this
> > > should be an actual IP address given it was a public static IP address -
> > > that was WRONG!
> > >
> > >
> > >
> > > Still wishing I could raise the volume on the iPhone Zoiper app in
> > speaker
> > > mode.  (Not an issue with Bluetooth car usage.)  This link gives an
> > example
> > > of adding a volume statement to the dial definition in extensions.conf:
> > >
> > >
> > >
> > > http://www.withsupport.co.uk/wiki/increasing-sip-volume-
> > freepbxasteriskelast
> > > ixtrixbox
> > >
> > >
> > >
> > > exten => s,1,Set(VOLUME(TX)=4)            ;can be any integer from 0 to
> > 10
> > >
> > > exten => s,1,Set(VOLUME(RX)=4)            ;can be any integer from 0 to
> > 10
> > >
> > >
> > >
> > > Tried that but with asterisk -rvvv monitoring, it reports "VOLUME not
> > > registered" so looks like this is not supported in our version.
> > >
> > >
> > >
> > > Any ideas on this?
> > >
> > >
> > >
> > > Tom N5TW
> > >
> > >
> > >
> > >
> > >
> > >
> >
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2 web page - http://hamvoip.org
> >
>