[arm-allstar] Transmitter Disable
Tom Robson
ve7did at dccnet.com
Thu Feb 26 00:23:53 EST 2015
Thx for the info Doug,
Finally got it figured out I believe.
You mentioned that the cmds you provided were not up to date. Where would one find
the up-to-date list?
...73 Tom ve7did
On Sun, 22 Feb 2015 21:51:29 -0500
Doug Crompton <doug at crompton.com> wrote:
> Tom,
>
> There are MANY commands to control things in Allstar... The status and COP, and
> ilink commands are what you want to look at. Here is a quick list but it is not up
> to date.
>
> * status cmds:
> *
> * 1 - Force ID (global)
> * 2 - Give Time of Day (global)
> * 3 - Give software Version (global)
> * 11 - Force ID (local only)
> * 12 - Give Time of Day (local only)
> *
> * cop (control operator) cmds:
> *
> * 1 - System warm boot
> * 2 - System enable
> * 3 - System disable
> * 4 - Test Tone On/Off
> * 5 - Dump System Variables on Console (debug)
> * 6 - PTT (phone mode only)
> * 7 - Time out timer enable
> * 8 - Time out timer disable
> * 9 - Autopatch enable
> * 10 - Autopatch disable
> * 11 - Link enable
> * 12 - Link disable
> * 13 - Query System State
> * 14 - Change System State
> * 15 - Scheduler Enable
> * 16 - Scheduler Disable
> * 17 - User functions (time, id, etc) enable
> * 18 - User functions (time, id, etc) disable
> * 19 - Select alternate hang timer
> * 20 - Select standard hang timer
> * 21 - Enable Parrot Mode
> * 22 - Disable Parrot Mode
> * 23 - Birdbath (Current Parrot Cleanup/Flush)
> * 24 - Flush all telemetry
> * 25 - Query last node un-keyed
> * 26 - Query all nodes keyed/unkeyed
> * 27 - Reset DAQ minimum on a pin
> * 28 - Reset DAQ maximum on a pin
> * 30 - Recall Memory Setting in Attached Xcvr
> * 31 - Channel Selector for Parallel Programmed Xcvr
> * 32 - Touchtone pad test: command + Digit string + # to playback all digits
> pressed
> * 33 - Local Telemetry Output Enable
> * 34 - Local Telemetry Output Disable
> * 35 - Local Telemetry Output on Demand
> * 36 - Foreign Link Local Output Path Enable
> * 37 - Foreign Link Local Output Path Disable
> * 38 - Foreign Link Local Output Path Follows Local Telemetry
> * 39 - Foreign Link Local Output Path on Demand
> * 40 - IRLP announce Enable
> * 41 - IRLP announce Disable
> * 42 - Echolink announce node # only
> * 43 - Echolink announce node Callsign only
> * 44 - Echolink announce node # & Callsign
> * 45 - Link Activity timer enable
> * 46 - Link Activity timer disable
> * 47 - Reset "Link Config Changed" Flag
> * 48 - Send Page Tone (Tone specs separated by parenthesis)
> * 49 - Disable incoming connections (control state noice)
> * 50 - Enable incoming connections (control state noicd)
> * 51 - Enable sleep mode
> * 52 - Disable sleep mode
> * 53 - Wake up from sleep
> * 54 - Go to sleep
> * 55 - Parrot Once if parrot mode is disabled
> *
> *
> * ilink cmds:
> *
> * 1 - Disconnect specified link
> * 2 - Connect specified link -- monitor only
> * 3 - Connect specified link -- tranceive
> * 4 - Enter command mode on specified link
> * 5 - System status
> * 6 - Disconnect all links
> * 11 - Disconnect a previously permanently connected link
> * 12 - Permanently connect specified link -- monitor only
> * 13 - Permanently connect specified link -- tranceive
> * 15 - Full system status (all nodes)
> * 16 - Reconnect links disconnected with "disconnect all links"
> * 200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)
> *
> * remote cmds:
> *
> * 1 - Recall Memory MM (*000-*099) (Gets memory from rpt.conf)
> * 2 - Set VFO MMMMM*KKK*O (Mhz digits, Khz digits, Offset)
> * 3 - Set Rx PL Tone HHH*D*
> * 4 - Set Tx PL Tone HHH*D* (Not currently implemented with DHE RBI-1)
> * 5 - Link Status (long)
> * 6 - Set operating mode M (FM, USB, LSB, AM, etc)
> * 100 - RX PL off (Default)
> * 101 - RX PL On
> * 102 - TX PL Off (Default)
> * 103 - TX PL On
> * 104 - Low Power
> * 105 - Med Power
> * 106 - Hi Power
> * 107 - Bump Down 20 Hz
> * 108 - Bump Down 100 Hz
> * 109 - Bump Down 500 Hz
> * 110 - Bump Up 20 Hz
> * 111 - Bump Up 100 Hz
> * 112 - Bump Up 500 Hz
> * 113 - Scan Down Slow
> * 114 - Scan Down Medium
> * 115 - Scan Down Fast
> * 116 - Scan Up Slow
> * 117 - Scan Up Medium
> * 118 - Scan Up Fast
> * 119 - Transmit allowing auto-tune
> * 140 - Link Status (brief)
> * 200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)
> *
> * playback cmds:
> * specify the name of the file to be played globally (for example, 25=rpt/foo)
> *
> * localplay cmds:
> * specify the name of the file to be played locally (for example, 25=rpt/foo)
> *
> * 'duplex' modes: (defaults to duplex=2)
> *
> * 0 - Only remote links key Tx and no main repeat audio.
> * 1 - Everything other then main Rx keys Tx, no main repeat audio.
> * 2 - Normal mode
> * 3 - Normal except no main repeat audio.
> * 4 - Normal except no main repeat audio during autopatch only
> *
>
> 73 Doug
> WA3DSP
> http://www.crompton.com/hamradio
>
>
> > Date: Sun, 22 Feb 2015 12:26:47 -0800
> > From: ve7did at dccnet.com
> > To: arm-allstar at hamvoip.org
> > Subject: [arm-allstar] Transmitter Disable
> >
> > Still new to this so trying to find my way...
> >
> > Have 2 nodes set up with full duplex repeater connected to each node (vhf & uhf).
> > These 2 repeaters are normally linked together. They are at different physical
> > locations.
> >
> > Trying to figure out how to disable the transmitters at each site
> > (independently) if for some reason the repeaters are subject to abuse or
> > interference. Also the same scenario applies to the CTCCS at the sites.
> >
> > Is there a macro or some way to control these functions?
> >
> > Hope this makes sense.
> >
> > ...73 Tom ve7did
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
> >
>
More information about the arm-allstar
mailing list