[arm-allstar] Transmitter Disable

Sun Feb 22 21:51:29 EST 2015

Tom,

 There are MANY commands to control things in Allstar... The status and COP, and ilink commands are what you want to look at. Here is a quick list but it is not up to date.

* status cmds:
 *
 *  1 - Force ID (global)
 *  2 - Give Time of Day (global)
 *  3 - Give software Version (global)
 *  11 - Force ID (local only)
 *  12 - Give Time of Day (local only)
 *
 * cop (control operator) cmds:
 *
 *  1 - System warm boot
 *  2 - System enable
 *  3 - System disable
 *  4 - Test Tone On/Off
 *  5 - Dump System Variables on Console (debug)
 *  6 - PTT (phone mode only)
 *  7 - Time out timer enable
 *  8 - Time out timer disable
 *  9 - Autopatch enable
 *  10 - Autopatch disable
 *  11 - Link enable
 *  12 - Link disable
 *  13 - Query System State
 *  14 - Change System State
 *  15 - Scheduler Enable
 *  16 - Scheduler Disable
 *  17 - User functions (time, id, etc) enable
 *  18 - User functions (time, id, etc) disable
 *  19 - Select alternate hang timer
 *  20 - Select standard hang timer 
 *  21 - Enable Parrot Mode
 *  22 - Disable Parrot Mode
 *  23 - Birdbath (Current Parrot Cleanup/Flush)
 *  24 - Flush all telemetry
 *  25 - Query last node un-keyed
 *  26 - Query all nodes keyed/unkeyed
 *  27 - Reset DAQ minimum on a pin
 *  28 - Reset DAQ maximum on a pin
 *  30 - Recall Memory Setting in Attached Xcvr
 *  31 - Channel Selector for Parallel Programmed Xcvr
 *  32 - Touchtone pad test: command + Digit string + # to playback all digits pressed
 *  33 - Local Telemetry Output Enable
 *  34 - Local Telemetry Output Disable
 *  35 - Local Telemetry Output on Demand
 *  36 - Foreign Link Local Output Path Enable
 *  37 - Foreign Link Local Output Path Disable
 *  38 - Foreign Link Local Output Path Follows Local Telemetry
 *  39 - Foreign Link Local Output Path on Demand
 *  40 - IRLP announce Enable
 *  41 - IRLP announce Disable
 *  42 - Echolink announce node # only
 *  43 - Echolink announce node Callsign only
 *  44 - Echolink announce node # & Callsign
 *  45 - Link Activity timer enable
 *  46 - Link Activity timer disable
 *  47 - Reset "Link Config Changed" Flag 
 *  48 - Send Page Tone (Tone specs separated by parenthesis)
 *  49 - Disable incoming connections (control state noice)
 *  50 - Enable incoming connections (control state noicd)
 *  51 - Enable sleep mode
 *  52 - Disable sleep mode
 *  53 - Wake up from sleep
 *  54 - Go to sleep
 *  55 - Parrot Once if parrot mode is disabled
 *
 *
 * ilink cmds:
 *
 *  1 - Disconnect specified link
 *  2 - Connect specified link -- monitor only
 *  3 - Connect specified link -- tranceive
 *  4 - Enter command mode on specified link
 *  5 - System status
 *  6 - Disconnect all links
 *  11 - Disconnect a previously permanently connected link
 *  12 - Permanently connect specified link -- monitor only
 *  13 - Permanently connect specified link -- tranceive
 *  15 - Full system status (all nodes)
 *  16 - Reconnect links disconnected with "disconnect all links"
 *  200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)
 *
 * remote cmds:
 *
 *  1 - Recall Memory MM  (*000-*099) (Gets memory from rpt.conf)
 *  2 - Set VFO MMMMM*KKK*O   (Mhz digits, Khz digits, Offset)
 *  3 - Set Rx PL Tone HHH*D*
 *  4 - Set Tx PL Tone HHH*D* (Not currently implemented with DHE RBI-1)
 *  5 - Link Status (long)
 *  6 - Set operating mode M (FM, USB, LSB, AM, etc)
 *  100 - RX PL off (Default)
 *  101 - RX PL On
 *  102 - TX PL Off (Default)
 *  103 - TX PL On
 *  104 - Low Power
 *  105 - Med Power
 *  106 - Hi Power
 *  107 - Bump Down 20 Hz
 *  108 - Bump Down 100 Hz
 *  109 - Bump Down 500 Hz
 *  110 - Bump Up 20 Hz
 *  111 - Bump Up 100 Hz
 *  112 - Bump Up 500 Hz
 *  113 - Scan Down Slow
 *  114 - Scan Down Medium
 *  115 - Scan Down Fast
 *  116 - Scan Up Slow
 *  117 - Scan Up Medium
 *  118 - Scan Up Fast
 *  119 - Transmit allowing auto-tune
 *  140 - Link Status (brief)
 *  200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)
 *
 * playback cmds:
 *  specify the name of the file to be played globally (for example, 25=rpt/foo)
 *
 * localplay cmds:
 * specify the name of the file to be played locally (for example, 25=rpt/foo)
 *
 * 'duplex' modes:  (defaults to duplex=2)
 *
 * 0 - Only remote links key Tx and no main repeat audio.
 * 1 - Everything other then main Rx keys Tx, no main repeat audio.
 * 2 - Normal mode
 * 3 - Normal except no main repeat audio.
 * 4 - Normal except no main repeat audio during autopatch only
 *

73 Doug
WA3DSP
http://www.crompton.com/hamradio

> Date: Sun, 22 Feb 2015 12:26:47 -0800
> From: ve7did at dccnet.com
> To: arm-allstar at hamvoip.org
> Subject: [arm-allstar] Transmitter Disable
> 
> Still new to this so trying to find my way...
> 
> Have 2 nodes set up with full duplex repeater connected to each node (vhf & uhf).
> These 2 repeaters are normally linked together. They are at different physical
> locations.
> 
> Trying to figure out how to disable the transmitters at each site (independently) if
> for some reason the repeaters are subject to abuse or interference.  Also the same
> scenario applies to the CTCCS at the sites.
> 
> Is there a macro or some way to control these functions?
> 
> Hope this makes sense.
> 
> ...73 Tom ve7did
> _______________________________________________
> 
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> 
> Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
> 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20150222/5a760452/attachment.html>