[arm-allstar] Transmitter Disable
Doug Crompton
doug at crompton.com
Thu Feb 26 02:05:42 EST 2015
Tom,
I will put it on my list of things to do and hopefully get to it soon. What you have is mostly correct. There were a few changes on the BBB like *73 permanent connect and *71 permanent disconnect and a few others.
73 Doug
WA3DSP
http://www.crompton.com/hamradio
> Date: Wed, 25 Feb 2015 21:23:53 -0800
> From: ve7did at dccnet.com
> To: arm-allstar at hamvoip.org
> Subject: Re: [arm-allstar] Transmitter Disable
>
> Thx for the info Doug,
> Finally got it figured out I believe.
> You mentioned that the cmds you provided were not up to date. Where would one find
> the up-to-date list?
>
> ...73 Tom ve7did
>
>
>
> On Sun, 22 Feb 2015 21:51:29 -0500
> Doug Crompton <doug at crompton.com> wrote:
>
> > Tom,
> >
> > There are MANY commands to control things in Allstar... The status and COP, and
> > ilink commands are what you want to look at. Here is a quick list but it is not up
> > to date.
> >
> > * status cmds:
> > *
> > * 1 - Force ID (global)
> > * 2 - Give Time of Day (global)
> > * 3 - Give software Version (global)
> > * 11 - Force ID (local only)
> > * 12 - Give Time of Day (local only)
> > *
> > * cop (control operator) cmds:
> > *
> > * 1 - System warm boot
> > * 2 - System enable
> > * 3 - System disable
> > * 4 - Test Tone On/Off
> > * 5 - Dump System Variables on Console (debug)
> > * 6 - PTT (phone mode only)
> > * 7 - Time out timer enable
> > * 8 - Time out timer disable
> > * 9 - Autopatch enable
> > * 10 - Autopatch disable
> > * 11 - Link enable
> > * 12 - Link disable
> > * 13 - Query System State
> > * 14 - Change System State
> > * 15 - Scheduler Enable
> > * 16 - Scheduler Disable
> > * 17 - User functions (time, id, etc) enable
> > * 18 - User functions (time, id, etc) disable
> > * 19 - Select alternate hang timer
> > * 20 - Select standard hang timer
> > * 21 - Enable Parrot Mode
> > * 22 - Disable Parrot Mode
> > * 23 - Birdbath (Current Parrot Cleanup/Flush)
> > * 24 - Flush all telemetry
> > * 25 - Query last node un-keyed
> > * 26 - Query all nodes keyed/unkeyed
> > * 27 - Reset DAQ minimum on a pin
> > * 28 - Reset DAQ maximum on a pin
> > * 30 - Recall Memory Setting in Attached Xcvr
> > * 31 - Channel Selector for Parallel Programmed Xcvr
> > * 32 - Touchtone pad test: command + Digit string + # to playback all digits
> > pressed
> > * 33 - Local Telemetry Output Enable
> > * 34 - Local Telemetry Output Disable
> > * 35 - Local Telemetry Output on Demand
> > * 36 - Foreign Link Local Output Path Enable
> > * 37 - Foreign Link Local Output Path Disable
> > * 38 - Foreign Link Local Output Path Follows Local Telemetry
> > * 39 - Foreign Link Local Output Path on Demand
> > * 40 - IRLP announce Enable
> > * 41 - IRLP announce Disable
> > * 42 - Echolink announce node # only
> > * 43 - Echolink announce node Callsign only
> > * 44 - Echolink announce node # & Callsign
> > * 45 - Link Activity timer enable
> > * 46 - Link Activity timer disable
> > * 47 - Reset "Link Config Changed" Flag
> > * 48 - Send Page Tone (Tone specs separated by parenthesis)
> > * 49 - Disable incoming connections (control state noice)
> > * 50 - Enable incoming connections (control state noicd)
> > * 51 - Enable sleep mode
> > * 52 - Disable sleep mode
> > * 53 - Wake up from sleep
> > * 54 - Go to sleep
> > * 55 - Parrot Once if parrot mode is disabled
> > *
> > *
> > * ilink cmds:
> > *
> > * 1 - Disconnect specified link
> > * 2 - Connect specified link -- monitor only
> > * 3 - Connect specified link -- tranceive
> > * 4 - Enter command mode on specified link
> > * 5 - System status
> > * 6 - Disconnect all links
> > * 11 - Disconnect a previously permanently connected link
> > * 12 - Permanently connect specified link -- monitor only
> > * 13 - Permanently connect specified link -- tranceive
> > * 15 - Full system status (all nodes)
> > * 16 - Reconnect links disconnected with "disconnect all links"
> > * 200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)
> > *
> > * remote cmds:
> > *
> > * 1 - Recall Memory MM (*000-*099) (Gets memory from rpt.conf)
> > * 2 - Set VFO MMMMM*KKK*O (Mhz digits, Khz digits, Offset)
> > * 3 - Set Rx PL Tone HHH*D*
> > * 4 - Set Tx PL Tone HHH*D* (Not currently implemented with DHE RBI-1)
> > * 5 - Link Status (long)
> > * 6 - Set operating mode M (FM, USB, LSB, AM, etc)
> > * 100 - RX PL off (Default)
> > * 101 - RX PL On
> > * 102 - TX PL Off (Default)
> > * 103 - TX PL On
> > * 104 - Low Power
> > * 105 - Med Power
> > * 106 - Hi Power
> > * 107 - Bump Down 20 Hz
> > * 108 - Bump Down 100 Hz
> > * 109 - Bump Down 500 Hz
> > * 110 - Bump Up 20 Hz
> > * 111 - Bump Up 100 Hz
> > * 112 - Bump Up 500 Hz
> > * 113 - Scan Down Slow
> > * 114 - Scan Down Medium
> > * 115 - Scan Down Fast
> > * 116 - Scan Up Slow
> > * 117 - Scan Up Medium
> > * 118 - Scan Up Fast
> > * 119 - Transmit allowing auto-tune
> > * 140 - Link Status (brief)
> > * 200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)
> > *
> > * playback cmds:
> > * specify the name of the file to be played globally (for example, 25=rpt/foo)
> > *
> > * localplay cmds:
> > * specify the name of the file to be played locally (for example, 25=rpt/foo)
> > *
> > * 'duplex' modes: (defaults to duplex=2)
> > *
> > * 0 - Only remote links key Tx and no main repeat audio.
> > * 1 - Everything other then main Rx keys Tx, no main repeat audio.
> > * 2 - Normal mode
> > * 3 - Normal except no main repeat audio.
> > * 4 - Normal except no main repeat audio during autopatch only
> > *
> >
> > 73 Doug
> > WA3DSP
> > http://www.crompton.com/hamradio
> >
> >
> > > Date: Sun, 22 Feb 2015 12:26:47 -0800
> > > From: ve7did at dccnet.com
> > > To: arm-allstar at hamvoip.org
> > > Subject: [arm-allstar] Transmitter Disable
> > >
> > > Still new to this so trying to find my way...
> > >
> > > Have 2 nodes set up with full duplex repeater connected to each node (vhf & uhf).
> > > These 2 repeaters are normally linked together. They are at different physical
> > > locations.
> > >
> > > Trying to figure out how to disable the transmitters at each site
> > > (independently) if for some reason the repeaters are subject to abuse or
> > > interference. Also the same scenario applies to the CTCCS at the sites.
> > >
> > > Is there a macro or some way to control these functions?
> > >
> > > Hope this makes sense.
> > >
> > > ...73 Tom ve7did
> > > _______________________________________________
> > >
> > > arm-allstar mailing list
> > > arm-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
> > >
> >
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20150226/7821f123/attachment-0001.html>
More information about the arm-allstar
mailing list