[Arm-allstar-irlp] Connection failures

Tue Apr 10 22:30:12 EST 2018

If Ron is building a new debian server to get a key he would have to
shutoff the port forwarding to the hamvoip server if he set that up and
then create that same forwarding to the debian server. Then get the key,
transfer it to the hamvoip server and reverse the port forwarding back to
the hamvoip server.

*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*

On Tue, Apr 10, 2018 at 11:19 PM, Darrell Wilkinson <kc5czx at gmail.com>
wrote:

> I must admit its been awhile since I made a irlp node that way but if
> memory serves you should have had the node# by the end of the install. Now
> should be the time for that node# to populate the server and become active.
> Currently I have no want or need to build up another irlp node to find out
> what or where something went wrong. If you have your port forwarding set
> right being behind a router should not make a difference and im guessing
> just wait to see what node# you get. Other then that you may need to run it
> again if no new node# is assigned. Something somewhere in the install went
> wrong.
>
> On Apr 10, 2018 9:50 PM, "Ronald Foster" <rf37797 at gmail.com> wrote:
>
> So far, so good. I submitted the installs email with my IP address, root
> password, and NEW node request.
>
> I’m concerned that since my Pi and software are behind my router, the only
> address I could logically give them was that of my routers to the network.
> I don’t see how they would be capable of installing any key.
>
> I haven’t a clue what they really need to get into my Pi, which is behind
> my router with an in-house address of 192.168.1.21.
>
> You know what I need to supple them?
>
> Thank you for you help and concern.
>
> Ron
>
> On Apr 10, 2018, at 9:11 PM, Darrell Wilkinson <kc5czx at gmail.com> wrote:
>
> Well Ron how did your node project come out I hope it worked for you as
> well as it worked for me
>
> On Tue, Apr 10, 2018, 1:56 PM Darrell Wilkinson <kc5czx at gmail.com> wrote:
>
>> Very good i've made a few irlp node using the full desktop version so I
>> know it should work for you to
>>
>> On Tue, Apr 10, 2018, 1:50 PM Ronald Foster <rf37797 at gmail.com> wrote:
>>
>>> Thank you so very much! I’m downloading it now.
>>>
>>> 73
>>>
>>> Ron, K0AAJ
>>>
>>> On Apr 10, 2018, at 12:47 PM, Darrell Wilkinson <kc5czx at gmail.com>
>>> wrote:
>>>
>>> Ron I have a copy of Jessie full desktop you can do the same thing on it
>>> just don''t delete the pi user, I have copied it off to one of my nodes and
>>> you can download it from there. Use WinSCP to login to this ip username is
>>> root password is wilky123 ssh 222 and you will find it in the /root
>>> directory it is at the bottom of the list
>>>
>>> 99.98.90.235
>>>
>>> On Tue, Apr 10, 2018 at 11:06 AM, Ronald Foster <rf37797 at gmail.com>
>>> wrote:
>>>
>>>> Thanks Darrell.
>>>>
>>>> Unfortunately, I cannot find a download of the Debian Jessie Lite. The
>>>> setup instructions would not allow me to complete the IRLP download setup.
>>>>
>>>> I guess I’ll buy the software IRPL pre-load on a SD card.
>>>>
>>>> Thanks.
>>>>
>>>> On Apr 10, 2018, at 8:21 AM, Darrell Wilkinson <kc5czx at gmail.com>
>>>> wrote:
>>>>
>>>> Ron you don't need to buy another V3 board download a copy of raspbian
>>>> lite then follow instruction given here
>>>>
>>>> http://www.irlp.net/pi/directions.txt
>>>>
>>>> I'm guessing you will need to make a New node so at the prompt type in
>>>> NEW.
>>>> During the install it will ask you purchase date and a few other
>>>> questions in those type in USED all caps. After the install is finished
>>>> give it a few to let the servers catch up to your new node# then make a
>>>> backup from that. Once it shows on the irlp servers you just need to take
>>>> out the files you need to build your TriStar. I have made several irlp
>>>> nodes in this manor and none of them have I had a V3 board
>>>>
>>>>
>>>> On Mon, Apr 9, 2018 at 9:30 AM, Ronald Foster <rf37797 at gmail.com>
>>>> wrote:
>>>>
>>>>> Thanks for the reply. No, he has actually receive the node, so I’m
>>>>> sure it has been used yet.
>>>>>
>>>>> What do you mean about not needing a IRLP V3 board to make a new node?
>>>>> I was about to purchase new node from David at IRLP just to have a new key
>>>>> issued.
>>>>>
>>>>> 73
>>>>>
>>>>> Ron
>>>>>
>>>>> On Apr 9, 2018, at 9:17 AM, Darrell Wilkinson <kc5czx at gmail.com>
>>>>> wrote:
>>>>>
>>>>> Do you know if the node you sold is being used, If so irlp will kick
>>>>> out the second same node#. It might be easier if you made a new irlp node#
>>>>> and use that. You don't need a irlp V3 board to make a new node# just type
>>>>> in USED for purchase date and whatever else during install
>>>>>
>>>>> On Mon, Apr 9, 2018 at 9:06 AM, Ronald Foster <rf37797 at gmail.com>
>>>>> wrote:
>>>>>
>>>>>> I believe I have everything installed and configured for IRLP, but
>>>>>> when I try to connect I always have a "connection failed" message.
>>>>>>
>>>>>> I do see the call attempting to link-up, but drops after a few
>>>>>> seconds.
>>>>>>
>>>>>> I tried 2 nodes and 2 reflector and get the same message.
>>>>>>
>>>>>> Oddly, my 4386 node is displayed twice in the IRLP Summary, so I'm
>>>>>> not sure if there is a problem with the IRLP network as it related to my
>>>>>> node.
>>>>>>
>>>>>> I was hoping to get my server working properly today, since I sold my
>>>>>> Nano Node and I'm using its key.
>>>>>>
>>>>>> I cannot continue to use the key after the new owner brings it online
>>>>>> this evening.
>>>>>>
>>>>>> Any ideas?
>>>>>>
>>>>>> Ron, K0AAJ
>>>>>>
>>>>>> _______________________________________________
>>>>>> Arm-allstar-irlp mailing list
>>>>>> Arm-allstar-irlp at hamvoip.org
>>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>>>>>>
>>>>>>
>>>>> _______________________________________________
>>>>> Arm-allstar-irlp mailing list
>>>>> Arm-allstar-irlp at hamvoip.org
>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Arm-allstar-irlp mailing list
>>>>> Arm-allstar-irlp at hamvoip.org
>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>>>>>
>>>>>
>>>> _______________________________________________
>>>> Arm-allstar-irlp mailing list
>>>> Arm-allstar-irlp at hamvoip.org
>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>>>>
>>>>
>>>> _______________________________________________
>>>> Arm-allstar-irlp mailing list
>>>> Arm-allstar-irlp at hamvoip.org
>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>>>>
>>>>
>>> _______________________________________________
>>> Arm-allstar-irlp mailing list
>>> Arm-allstar-irlp at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>>>
>>> _______________________________________________
>>> Arm-allstar-irlp mailing list
>>> Arm-allstar-irlp at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>>>
>> _______________________________________________
> Arm-allstar-irlp mailing list
> Arm-allstar-irlp at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>
> _______________________________________________
> Arm-allstar-irlp mailing list
> Arm-allstar-irlp at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>
>
>
> _______________________________________________
> Arm-allstar-irlp mailing list
> Arm-allstar-irlp at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar-irlp
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar-irlp/attachments/20180410/fb5e74c8/attachment.html>