[arm-allstar] HamVoip Not Booting on RPi 3A+

[David McGough]

Tony,

It's worth comparing the checksum of the file you downloaded with the 
published checksum on the hamvoip.org website, just to make sure the file 
isn't corrupted.

https://hamvoip.org/#download

73, David K4FXC


On Wed, 22 Nov 2023, Tony Loera via ARM-allstar wrote:

>  Hi Michael,
Yes, writing the img file with Win32 after unziping V1.7.
Dave,
I tried 2 different computers now with three different MicroSD Cards and still nothing.  I also updated the Pi's firmware to no avail. 
Could it be that I have a newer revision board (1.1)?
    On Tuesday, November 21, 2023 at 03:24:37 PM PST, Michael Webb via ARM-allstar <arm-allstar at hamvoip.org> wrote:  
 
 Are you writing a .img file to the sd card?

On Tue, Nov 21, 2023, 4:06 PM Tony Loera via ARM-allstar <
arm-allstar at hamvoip.org> wrote:

>  Just gave it shot, no luck.  I also tried Dave's image (WA2KJC) with no
> luck (both written with Win32 Imager).  Both give me the same light pattern
> almost immediately (insufficient power), regardless of power supply.
> I keep wanting to think the board is defective, but it runs the Raspberry
> OS just fine.
>Â  Â  On Tuesday, November 21, 2023 at 01:09:06 PM PST, David McGough <
> kb4fxc at inttek.net> wrote:
>
>
> Tony,
>
> Yes, use the Win32 Disk Imager software included with the download HamVoIP
> firmware.  The Rasbian imager probably won't work correctly.
>
> 73, David K4FXC
>
>
> On Tue, 21 Nov 2023, Tony Loera wrote:
>
> >Â  Hi David,
> > I downloaded the same img.xz file from this link and used RPi Imager to
> flash it to the SD Card.  Should I be using Win32 instead?Â
> > -TonyÂ
> >Â  Â  On Tuesday, November 21, 2023 at 05:42:22 AM PST, David McGough <
> kb4fxc at inttek.net> wrote:
> >
> >
> > Tony,
> >
> > Which HamVoIP image did you download and how did you flash it to the SD
> > card?  These images should work with the RPi3A+ boards:
> >
> > https://hamvoip.org/RPi2/RPi-Z2W-2-3-4_V1.7-01_Allstar.exe
> > https://hamvoip.org/RPi2/RPi-Z2W-2-3-4_V1.7-01_Allstar.img.xz
> >
> > Note that both of these files are compressed, so you must uncompress
> > first.
> >
> > 73, David K4FXC
> >
> >
> >
> > On Tue, 21 Nov 2023, Tony Loera via ARM-allstar wrote:
> >
> > > I just picked up a new RPi 3A+ and loaded a fresh image of the latest
> HamVoip onto a 32GB MicroSD card and the thing wont boot.  I tried
> different cards as well as working cards and 3 different power supplies but
> all I get is 4-steady, and 7 fast blinking green lights.
> > Funny thing is that the Raspberry OS Runs just fine, but HamVoip just
> won't boot.  Board revision is 1.1.
> > I am out of ideas ÂÂ
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> >
> >
>
>
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>
_______________________________________________

ARM-allstar mailing list
ARM-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
  
_______________________________________________

ARM-allstar mailing list
ARM-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2/3/4 web page - http://hamvoip.org