[arm-allstar] Two nodes on same server Pi3+

[Ron WA2WWK]

Thanks.  Actually, on the radio-less node, the audio from both nodes
announce the ip address, node number and what node connected to (auto
connect) are announced.  I hope to be able to mute or lower the volume of
this audio announcement and allow the telemetry tones.  I already have
changed the level to -6 & -9.  Please see:
* ;idrecording=/etc/asterisk/local/node-id      ; Main ID voice*

*;idrecording=|iDE 62B0F5DCA971/L              ; Main ID CW*

*;idtalkover=|iDE 62B0F5DCA971/L                ; ID when signal present*

*;idrecording=|iDE WA2WWK/L*


I thought commenting out the above lines would solve the problem but
doesn't seem to make a difference?  I'll try the telemetry tone adjustments
as you suggested.  Thanks.  Ron

On Wed, Jun 23, 2021 at 3:03 PM "Mark VE3JMR via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> Hi
>
> You have two options when editing /etc/asterisk/rpt.conf
>
> 1. While not muted, you can change the telemetry audio levels. Search
> for "Audio Level settings in dB" and change one or both settings. I have
> mine set for -6 and -9 respectfully.  (Reminder if you were not aware,
> -3dB is the equivalent to reducing audio by 50%, -6dB by 75%, -9dB by
> 87%) A setting of at least -18dB would be the effective near equivalency
> of muting. Note that these settings do not disable telemetry but affect
> telemetry audio level.
>
> 2. Search for "Misc. settings". Change telemdefault=x to one of the
> three settings. I have mine set to 2. This sends only telemetry for the
> actions I initiate and then mutes telemetry after 1 minute. Also look at
> holdofftelem=x. See comments in file for descriptions.
>
> Courtesy tones: You can change each node's tones and have up to three
> tones per node depending on your preference. Find "Courtesy Tone
> mapping" and review the three settings. You can use the defaults shown,
> change them to one of the other definitions under "Courtesy Tone
> definitions" near the bottom of the config file or  create your own
> custom definitions.
>
> For easy to read details, download this document:
>
> https://hamvoip.org/howto/courtesy_tone_howto.pdf
>
> All of these settings must be edited for each node. Remember to reboot
> AST and/or the server for the configuration changes to take place.
>
> 73 75 de VE3JMR
>  Mark
>  Port Colborne, Ontario
>  CANADA
>  https://www.qrz.com/db/VE3JMR
>  Allstar Node# 53132
>
> LIFE has an expiry date.
>  <if trumpet=%true then exit function>
>
> > Message: 1
> > Date: Tue, 22 Jun 2021 21:00:29 -0400
> > From: Ron  WA2WWK <wa2wwk at gmail.com>
> > To: ARM Allstar <arm-allstar at hamvoip.org>
> > Subject: [arm-allstar] Two nodes on same server Pi3+
> >
> > Presently I have 2 nodes on the same server.  First node is a radio node,
> > while the second node is a radio-less node with a hard wire speaker and
> > microphone.  Both use an auto connect upon boot-up.  I would like to have
> > only the telemetry confirmation connect tone (maybe a different frequency
> > tone) with the voice announcement muted on the radio-less node.
> Presently
> > both nodes auto connect to the same external node.   I've tried to
> comment
> > several lines in the rpt.conf file  without success.  Any suggestions are
> > appreciated.  Thanks. WA2WWK
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>