[arm-allstar] Rx only site

[Tom Eaton]

There is no ptt on the remote receiver, and I have done the cop3 and the
problem is as you stated that it will not allow connections, so if the
remote receiver drops it cannot reconnect. Thanks for the info, I guess it
is what it is, everything has it's limits.
Tom, KC4CBQ

On Sun, May 17, 2020, 4:16 PM "Doug Crompton via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> So you can't just physically disconnect the PTT on that node?  cop 2 and 3
> turn TX on and off BUT when off it also disallows any connects. If you
> connect first then turn off the TX it should work allowing only RX from
> that node but no other connects TO that node.
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>
>
> On Sun, May 17, 2020 at 4:04 PM "Tom Eaton via ARM-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > OK, Doug
> > The rx is at a remote location that can call out but not incoming, so the
> > remote node is set up to connect out to the tx site at boot, so I cannot
> > have the tx site connect to the rx site in monitor only. that is why I am
> > looking for a way to disable ptt at rx node.
> >
> > Thanks
> > Tom
> >
> > On Sun, May 17, 2020 at 2:02 PM "Doug Crompton via ARM-allstar" <
> > arm-allstar at hamvoip.org> wrote:
> >
> > > Tom,
> > >
> > >   Maybe I am not understanding what you want to do but isn't this what
> > > monitor mode does? Rx only from a node,
> > >
> > >
> > > *73 Doug*
> > >
> > > *WA3DSP*
> > >
> > > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> > >
> > >
> > > On Sun, May 17, 2020 at 1:06 PM "Tom Eaton via ARM-allstar" <
> > > arm-allstar at hamvoip.org> wrote:
> > >
> > > > Is there a setting in rpt.conf so I can disable ptt on a rx node
> only,
> > I
> > > > want it to work just as it does if the rx node is connected to the tx
> > > node,
> > > > but if I set the rx node to repeater disable it works the way I want
> it
> > > to.
> > > > I have it set duplex=0, but on the rx node it shows ptt back from the
> > tx
> > > > node which makes rx node unable to then receive be cause it is in tx
> .
> > I
> > > > need traffic in one way from rx node to tx only.
> > > >
> > > > Thanks
> > > > Tom
> > > >
> > > > <
> > > >
> > >
> >
> https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=icon
> > > > >
> > > > Virus-free.
> > > > www.avast.com
> > > > <
> > > >
> > >
> >
> https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=link
> > > > >
> > > > <#m_8778912918431924907_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
> > > > _______________________________________________
> > > >
> > > > ARM-allstar mailing list
> > > > ARM-allstar at hamvoip.org
> > > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > > >
> > > > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> > > >
> > > _______________________________________________
> > >
> > > ARM-allstar mailing list
> > > ARM-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> > >
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> >
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>