[arm-allstar] Macro Not Found

[Doug Crompton]

Yes, but this was a new user and there were other problems besides DTMF.
Always happy to help new users.


*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*

On Sun, Mar 22, 2020 at 10:51 AM "Jay Urish via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> And folks,
>
> This is why you LOOK AT THE LOGS!
>
>
> On 3/21/20 11:16 PM, "Doug Crompton via ARM-allstar" wrote:
> > This was resolved but since we did it off-line I wanted to at least tell
> > everyone the resolution. The system was not setup properly for some
> reason
> > so I did a setup for him remotely and at that point all was well but then
> > when he went to connect somewhere he got the Macro not found message. It
> > turns out that the 3 digit was not working on his handheld DTMF and when
> he
> > tried to connect he was doing *35....  And instead it was doing *5....
> and
> > looking for a macro!
> >
> >
> > *73 Doug*
> >
> > *WA3DSP*
> >
> > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> >
> > On Sat, Mar 21, 2020 at 10:48 AM Doug Crompton <wa3dsp at gmail.com> wrote:
> >
> >> Jerry,
> >>
> >>   First of all this has nothing to do with your hardware (repeater etc.)
> >> Rather than going back and forth in emails can you send me privately
> your
> >> node number and login password so I can login and look at it. You need
> to
> >> have port 222 forwarded in your router and the node running. Also give
> me
> >> your phone number.  My email is wa3dsp at gmail.com
> >>
> >>
> >> *73 Doug*
> >>
> >> *WA3DSP*
> >>
> >> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> >>
> >> On Sat, Mar 21, 2020 at 1:33 AM "David McGough via ARM-allstar" <
> >> arm-allstar at hamvoip.org> wrote:
> >>
> >>>
> >>> Hello Everyone,
> >>>
> >>> I have an issue that I cannot get past. I am setting up a repeater
> >>> using a CDM 1550 for TX and a CDM 750 for RX.
> >>>
> >>> I have re-flashed the micro usb several time to try different setup
> >>> configurations and nothing I do seem to change my problem. After the
> setup
> >>> is complete I try to connect to a 6 digit node and I get the response
> >>> "macro not found" but the 6 digit node can connect to mine. When I try
> >>> toconnect to a 5 digit node I get a curiosity tone but no response
> that I
> >>> am connected to the node. When I watch it in Asterisk, I see the digits
> >>> but when I finish sending them the only response is a "hangup" Any help
> >>> would be greatly appreciated.
> >>>
> >>> Jerry Conner
> >>>
> >>>
> >>>
> >>> _______________________________________________
> >>>
> >>> ARM-allstar mailing list
> >>> ARM-allstar at hamvoip.org
> >>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>>
> >>> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> >>>
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>