[arm-allstar] hamvoip as a repeater controller

Sun Jan 26 22:10:54 EST 2020

Yes, They make custom cables


On 1/26/20 8:38 PM, "Jed Barton via ARM-allstar" wrote:
> Hey guys,
> So these guys at Noarthcom, do they do custom cables?  I know Marshal
> does as well. I always like to keep a running roster of technology
> venders.
>
> Cheers,
>
> Jed
>
> On 1/26/20, "John Simmons via ARM-allstar" <arm-allstar at hamvoip.org> wrote:
>> Larry,
>>
>> I purchased a mating connector to the MTR2K 96 pin cable from DigiKey
>> (p/n A1265-ND). I used the info from:
>> https://www.repeater-builder.com/motorola/mtr2k/mtr-interfacing/mtr2000-interfacing.html
>>
>> You'll need pin:
>> C2, receiver unsquelched, AKA COR. This pin is acitve HIGH, and you must
>> make this setting in SIMPLEUSB
>> C10, PTT. This pin is active LOW
>> A19 or B27 or C31 (all the same) GND.
>>
>> You must have the wireline board installed. Receive audio is on Wireline
>> connector pins 2- and 2+ (balanced audio, use either side for ground).
>> Transmit audio is on the same connector, pins 1- and 1+ with the same
>> note. I found this info on:
>> https://www.repeater-builder.com/motorola/mtr2k/more-mtr2k-int/mtr2000-interfacing-followup.html
>>
>> On reviewing this page it jogged my memory about programming. The link
>> above shows all the programming info you need. You will need the RSS to
>> set the transmit and receive levels. Be sure to read the HELP files in
>> the RSS, there is info there that isn't anywhere else.
>>
>> I realize I haven't given you a step-by-step guide but the info is there
>> for you. As far as the adaptor for the 96 pin connector you have I
>> didn't research that but the docs should tell you how to wire it up.
>>
>> I spent many years making equipment interconnections, especially between
>> different types and manufacturers. The key is reading all the docs you
>> can find and understanding what you are doing. If you still have
>> troubles shoot me an email. You can also trace signals on the wiring.
>> You'll need to tell me WHAT is happening, more than 'it doesn't work'.
>>
>> Good luck!
>>
>> -John NI0K
>>
>> "Larry Aycock via ARM-allstar" wrote on 1/26/2020 7:33 PM:
>>> Hello John,
>>>
>>> Thanks for the reply.  I spoke to Dave, AH6OD about this and he is
>>> offering some assistance.  Below is a copy and past of what I sent him.
>>> You'll note that we are using a ICS board to adapt the 96-pin connector to
>>> a 9-pin connect, and a cable built by Marshall Oldham.  However, the ICS
>>> board we purchased is the MTR2000 Linker II Adapter.  There is another ICS
>>> board that is a repeater adapter with a different pinout for the 9-pin
>>> connector, and now I'm wondering if that was our problem.  We both
>>> purchased the adapter that Marshall had sent me the link to, but perhaps
>>> it was the wrong adapter by mistake.  Anyway, below is an explanation of
>>> what we are trying to do.  At this point, it would be nice to just get
>>> AllStar to work with the MTR2000 so we know how to set it up.  Then we can
>>> see if we can get it to also work with the digital board.  I would think
>>> it should work together since the analog side is different from the
>>> digital side, but it depends on how the setup of the MTR2000 h
>>   as
>>>     to be for AllStar.
>>>
>>>
>>> To give a little background of what we have so far, below is a link to the
>>> device I was talking about which plugs into the 96-pin connector on the
>>> MTR2k.  When I was talking with Marshal Oldham, he pointed me to this
>>> device and said he has built cables for people to connect from this device
>>> to the URIx for use with AllStar.  So we purchased this board and had
>>> Marshall build us a cable.  However, we were not successful in getting it
>>> setup and working with HamVoip AllStar.  As I mentioned on the radio, we
>>> suspect we may not have setup the MTR2k correctly to work with the setup.
>>>
>>> MTR2000 Linker II Adapter
>>> https://ics-ctrl.com/product/mtr2000-linker-ii-adapter/
>>>
>>>
>>> Patrick does have the wireline board, however, he has it removed at the
>>> moment.  Currently, he has the MMDVM board linked below installed and
>>> working great to make the repeater a mixed-mode repeater, allowing users
>>> to use DMR, P25, NXDN, DStar, or, of course, analog.  My hope would be to
>>> have the same setup as a mixed mode repeater, but have the Allstar Pi
>>> control the analog side of things.  We can remove the digital board when
>>> we meet online to get things working just with AllStar at first.  That
>>> will allow us to know how to setup the repeater for AllStar.  Then, we can
>>> see about adding back in the digital board, and if they will work
>>> together.
>>>
>>> In the end, if we can't get both AllStar and the digital board to work
>>> together, Patrick will keep his repeater using the digital board for
>>> mixed-mode capabilities.  However, it will be good to at least know how to
>>> setup the MTR2k for Allstar as I may go that route in the future with my
>>> current repeater.  I may purchase an MTR-2000 in the future to replace the
>>> two CDM-1550's I have on my repeater.
>>>
>>>
>>> STM32-DVM-MTR2K Information
>>> http://ks-dmr.net/stm32-dvm-mtr2k-information/
>>>
>>>
>>> Thanks again for your offer to help.  I'm looking forward to getting this
>>> working.
>>>
>>> 73,
>>> Larry N6LKA
>>>
>>>
>>> -----Original Message-----
>>> From: ARM-allstar <arm-allstar-bounces at hamvoip.org> On Behalf Of "John
>>> Simmons via ARM-allstar"
>>> Sent: Sunday, January 26, 2020 4:46 PM
>>> To: ARM Allstar <arm-allstar at hamvoip.org>
>>> Cc: John Simmons <jasimmons at pinewooddata.com>
>>> Subject: Re: [arm-allstar] hamvoip as a repeater controller
>>>
>>> Larry,
>>>
>>> I've done this and it isn't hard. There isn't really anything different in
>>> the programming to affect the external connections. What are you having a
>>> problem with?
>>>
>>> -de John NI0K
>>>
>>> "Larry Aycock via ARM-allstar" wrote on 1/26/2020 1:03 PM:
>>>> Hi Darrell,
>>>>
>>>> A friend of mine has an MTR-2000, and we have tried setting up a RPi3
>>>> running HamVOIP Allstar, without success.  I was wondering if you could
>>>> share with me how you have the MTR-2k programmed to work with Allstar?
>>>> We aren't sure how to setup the programming of the repeater to get it to
>>>> work correct, and we suspect that may be our problem.  I'd appreciate any
>>>> help you can provide.  Feel free to email me directly at
>>>> N6LKA at outlook.com.
>>>>
>>>> 73,
>>>> Larry N6LKA
>>>>
>>>> -----Original Message-----
>>>> From: ARM-allstar <arm-allstar-bounces at hamvoip.org> On Behalf Of "Darrell
>>>> Black via ARM-allstar"
>>>> Sent: Friday, January 24, 2020 6:45 PM
>>>> To: ARM Allstar <arm-allstar at hamvoip.org>
>>>> Cc: Darrell Black <gigahacker at gmail.com>
>>>> Subject: Re: [arm-allstar] hamvoip as a repeater controller
>>>>
>>>> Hi Jed, I have a RPI3 running HAMVOIP's allstar running  a MTR2000 as a
>>>> talking controller and acting like a allstar and echolink node. No issues
>>>> works well. Checkout 50026 and do a bubble.
>>>>
>>>> On Fri, Jan 24, 2020 at 8:19 PM "Jed Barton via ARM-allstar" <
>>>> arm-allstar at hamvoip.org> wrote:
>>>>
>>>>> Hey guys,
>>>>>     Hope everyone is doing well.  OK, so i have a kenwood repeater.
>>>>> It's the tkr850.  At my site, i wanna have the hamvoip software run
>>>>> as a repeater controller and an allstar node.  I'm assuming that can
>>>>> be done.
>>>>> What would i need to configure in hamvoip?  I'm assuming you can do
>>>>> things with courtesy tones and all that?
>>>>>
>>>>> My plan is to plug the pi into the Kenwood repeater and have it do
>>>>> both.
>>>>> Any thoughts?
>>>>>
>>>>> Cheers,
>>>>>
>>>>> Jed
>>>>> _______________________________________________
>>>>>
>>>>> ARM-allstar mailing list
>>>>> ARM-allstar at hamvoip.org
>>>>> https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Flist
>>>>> s
>>>>> .hamvoip.org%2Fcgi-bin%2Fmailman%2Flistinfo%2Farm-allstar&data=02
>>>>> %
>>>>> 7C01%7C%7Cb63a8f2f01b54c6ad5d608d7a1416f0c%7C84df9e7fe9f640afb435aaaa
>>>>> a
>>>>> aaaaaaa%7C1%7C0%7C637155174733189594&sdata=%2Foz8PC5h%2FOxgkcDW62
>>>>> t
>>>>> BhnlRFSs9HKt5DkiFog9wA4A%3D&reserved=0
>>>>>
>>>>> Visit the BBB and RPi2/3/4 web page -
>>>>> https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fhamv
>>>>> o
>>>>> ip.org&data=02%7C01%7C%7Cb63a8f2f01b54c6ad5d608d7a1416f0c%7C84df9
>>>>> e
>>>>> 7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637155174733189594&sdata=owR
>>>>> v
>>>>> atDKMXxZ%2BNcsKukKcUekx%2FhLKGsF5hE9ERLPJCs%3D&reserved=0
>>>>>
>>> _______________________________________________
>>>
>>> ARM-allstar mailing list
>>> ARM-allstar at hamvoip.org
>>> https://nam02.safelinks.protection.outlook.com/?url=http%3A%2F%2Flists.hamvoip.org%2Fcgi-bin%2Fmailman%2Flistinfo%2Farm-allstar&data=02%7C01%7C%7Cb27d124f798a4e829a3608d7a2c4d4ac%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637156838587100711&sdata=oPjxOBlTLx%2F8teBj7ICiObwMJDa%2BccESBqPN%2FGFZtGU%3D&reserved=0
>>>
>>> Visit the BBB and RPi2/3/4 web page -
>>> https://nam02.safelinks.protection.outlook.com/?url=http%3A%2F%2Fhamvoip.org&data=02%7C01%7C%7Cb27d124f798a4e829a3608d7a2c4d4ac%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637156838587100711&sdata=GNeyjK16c2nsjJaaNZSq9Lj2uRJN454rMw5%2Fw0zMUc4%3D&reserved=0
>>> _______________________________________________
>>>
>>> ARM-allstar mailing list
>>> ARM-allstar at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>
>>> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>> _______________________________________________
>>
>> ARM-allstar mailing list
>> ARM-allstar at hamvoip.org
>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>
>> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>>
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org