[arm-allstar] No Audio in...

[Rick Dykstra]

Try a different radio. I have an HT that doesn’t decode properly
Rick


On Sat, Feb 8, 2020 at 6:38 PM "Doug Crompton via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> Cesar,
>
>  It is very hard to troubleshoot a hardware issue especially when you are
> using non-standard hardware. In your case the VOX circuit. I suggest you
> either modify the FOB and use it with true COS and PTT or buy one that is
> already modified. Sources are shown in the howto section st hamvoip.org.
> Using VOX is not a good idea and as you can see generally a PITA.
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>
>
> On Sat, Feb 8, 2020 at 3:22 PM Cesar Gonzalo <cesgonm at gmail.com> wrote:
>
> > Sorry to bother you...
> >
> > This is what is happening......
> > Simpleusb tune
> > Menu J  set to USB
> > When booting the system , it does not say anything...
> > If sending dtmf tones using cli i can see it recognized the tones....
> > But no audio back
> > After a couple of minutes it says node 51024 timeout
> > Picture 1
> >
> > If set to anything else
> > When booting the system , i says the ip address and id of the station
> > If sending dtmf tones using cli , nothing shows but if i input rpt fun
> *81
> > it does talk back
> > And there is no time out
> > Picture 2
> >
> > On Fri, Feb 7, 2020, 17:54 Doug Crompton <wa3dsp at gmail.com> wrote:
> >
> >> Cesar,
> >>
> >>  Using the main menu select simpleusb tune menu and you will see as
> >> below....
> >>
> >> Select item J to change to or from usb/usbinvert
> >>
> >> Select item K to key COS.  Then item 2 you should see audio on the
> >> bargraph display and set the level. It should go to 5Khz on peaks.. You
> can
> >> use K to manually key/unkey instead of the vox.
> >>
> >> Active simpleusb device stanza: [usb]
> ------------------------------------
> >> S) Select active USB device stanza
> >> V) View COS, CTCSS and PTT Telemetry using real-time display
> >> P) Print Current Parameter Values ---- 2) Set Rx Voice Level (using
> >> display)
> >> 3) Set Transmit A Level           ---- 4) Set Transmit B Level
> >> 5) Set Tx Audio Level Method (currently LOG)
> >> 7) Set Transmit DSP Level
> >> B) Toggle RX Boost Mode (currently Enabled)
> >> C) Toggle Echo Mode (currently Disabled)
> >> D) Flash (Toggle PTT and Tone output several times)
> >> E) Toggle Transmit Test Tone/Keying (currently Disabled)
> >> K) Manually key COS (currently Unkeyed)
> >> F) Toggle PRE-emphasis Mode (currently Disabled)
> >> G) Toggle DE-emphasis Mode (currently Disabled)
> >> H) Toggle PLfilter Mode (currently Disabled)
> >> Q) Toggle DCSfilter Mode (currently Enabled)
> >> I) Toggle PTT Mode (currently active LOW)
> >> J) Change COSFROM Mode (currently "usb")
> >> L) Change CTCSSFROM Mode (currently "no")
> >> M) Change RXONDELAY value (currently "0")
> >> N) Change RXAUDIODELAY value (currently "0")
> >> W) Write (Save) Current Parameter Values
> >> 0) Exit Menu
> >>
> >> Please enter your selection now:
> >>
> >>
> >> *73 Doug*
> >>
> >> *WA3DSP*
> >>
> >> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> >>
> >> On Fri, Feb 7, 2020 at 4:54 PM Cesar Gonzalo <cesgonm at gmail.com> wrote:
> >>
> >>> I know Vox is not a good idea , but for now , it is good enough to make
> >>> it easy.
> >>>
> >>> I did changed to usbinvert but still have the same issue, no response
> >>> when sendin *81 from other radio.
> >>>  Where I'm supposed to change to low or High
> >>>
> >>> On Fri, Feb 7, 2020, 15:13 "Doug Crompton via ARM-allstar" <
> >>> arm-allstar at hamvoip.org> wrote:
> >>>
> >>>> Just to be clear - I think I said simpleusb.conf - I meant simpleusb
> >>>> tune
> >>>> menu from the main hamvoip menu.
> >>>>
> >>>>
> >>>> *73 Doug*
> >>>>
> >>>> *WA3DSP*
> >>>>
> >>>> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> >>>>
> >>>> On Fri, Feb 7, 2020 at 12:42 PM "Cesar Gonzalo via ARM-allstar" <
> >>>> arm-allstar at hamvoip.org> wrote:
> >>>>
> >>>> > Hi to all , hope I can get some help with my node.
> >>>> >
> >>>> > First what I have :
> >>>> > Raspberry Pi 4
> >>>> > Usb fob cm-108 Unmodified
> >>>> > Easy digi Vox
> >>>> > Uv-5
> >>>> >
> >>>> > Trying to use vox , and it is working, but I can not get the audio
> in
> >>>> >
> >>>> > I can see the rx visual moving when I key , and when i send tones ,
> >>>> but not
> >>>> > answer back .
> >>>> >
> >>>> > Using CLI: Rpt fun 51024 *80 or others i get audio back.
> >>>> >
> >>>> > At the beginning it was giving me node xxxxx time out
> >>>> >
> >>>> > I changed the last cts.. to PP, and not giving me the time out any
> >>>> more.
> >>>> >
> >>>> > When reboot node , it give me ip address and ibsee the status green
> >>>> >
> >>>> > Problem
> >>>> >
> >>>> > When trying to send a tone *80 , seems that it is not recognized
> >>>> nothing
> >>>> > happend no reply
> >>>> >
> >>>> > I tried Parrot 1 , nothing too.
> >>>> >
> >>>> > I guess audio is not going trough,  even i I see it on the visual.
> >>>> >
> >>>> > Any help please.
> >>>> >
> >>>> > Thanks
> >>>> >
> >>>> > 73
> >>>> > _______________________________________________
> >>>> >
> >>>> > ARM-allstar mailing list
> >>>> > ARM-allstar at hamvoip.org
> >>>> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>>> >
> >>>> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> >>>> >
> >>>> _______________________________________________
> >>>>
> >>>> ARM-allstar mailing list
> >>>> ARM-allstar at hamvoip.org
> >>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>>>
> >>>> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> >>>>
> >>>
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>