[arm-allstar] Using Putty Problems at the Start

James Hause hausejd at gmail.com
Sun Oct 20 14:07:14 EDT 2019


Looks like you have not changed port number from 222 to 22 ??

On Sun, Oct 20, 2019 at 12:34 PM "Jeffrey Reid via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> Hello Stan,
>
> I do not have a monitor and keyboard, I have an old dell with windows 10,
> a MacBook pro.   And of course a router.  I li e in the hills..very rural.
> Our internet is a beam shot from my neighbors house through the trees to
> ours.  He supplies a few houses like that.  From town, the beam is shot to
> his house.  Rural living at its best.
>
> One ethernet cable is going from the router to the windows box, another to
> the node.  The windows box has an address of 105,  I finally determined
> that the node is 106.  So far, so good.  I have Putty, Kitty and all that.
> Okay, open up Putty and enter 222 for the port number and !!!!.106 for the
> address.  Terminal box comes up and after a while a box comes up and says
> Putty Failure, connection timed out.  (Sigh)…
>
> Jeffrey
>
> > On Oct 20, 2019, at 3:57 AM, stanley stanukinos via ARM-allstar <
> arm-allstar at hamvoip.org> wrote:
> >
> > Can you get into it with a monitor and keyboard? If so did you do an
> update? Did you also change the port to 222 from 22?
> >
> > Stan
> >
> > Sent from my iPhone
> >
> >> On Oct 20, 2019, at 1:29 AM, Jeffrey Reid via ARM-allstar <
> arm-allstar at hamvoip.org> wrote:
> >>
> >> Okay, this shouldn’t be that difficult, even for an OM that’s not
> computer savvy.  Did a clean write onto the SD card.  Checksum okay.
> Installed into Pi4.  Turn on and blinks dit-dit-dit-dah…The letter V I
> believe.  I try Putty and know that the ethernet IP connected to the Pi is
> .106 because I have another node (one of Mark’s nano-nodes).  Use port
> 222.  Keep getting connection timed out.  So I am stuck at the easy
> part…Jeez, what am I doing wrong.  I tried typing the IP into the Browser
> with no luck in getting a page that says TEST.
> >>
> >> The same cable is now back connected to my other node and working just
> fine, listening to the Insomniac Net.  Now, if I can only get to configure
> the new Pi4.  Any Ideas?
> >>
> >> Regards,
> >>
> >> Jeffrey
> >> _______________________________________________
> >>
> >> ARM-allstar mailing list
> >> ARM-allstar at hamvoip.org
> >> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>
> >> Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
>
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org


More information about the ARM-allstar mailing list