[arm-allstar] Using Putty Problems at the Start

Eric Harrison n7jys at yahoo.com
Sun Oct 20 13:22:10 EDT 2019


Yes, but it also allows HDMI hot plug. And still no HDMI video out either  way on the rpi3b+.
Eric (N7JYS) Marshall's Communications 

    On Sunday, October 20, 2019, 11:29:38 AM CDT, John Simmons via ARM-allstar <arm-allstar at hamvoip.org> wrote:  
 
 I believe the RPi requires the HDMI monitor be plugged in at power up in 
order for it to function.

-de John NI0K

"Eric Harrison via ARM-allstar" wrote on 10/20/2019 10:59 AM:
> Ok update. FYI I have just download the latest windows self extracting allstar image from hamvoip.org.
> I have only  rpi3b+'s to test this on. With a keyboard ,HDMI monitor, and usb sound fob plunged in,
> i have no video from the HDMI but audio out from the sound fob is fine. The default SSH port is now
> 222 per this firmware release. I was able to use putty to login in and confirm this.  There still seems to
> be an issue with HDMI video on the rpi3b+ with this firmware release. Can some one confirm this
> before i address this as an issue? Thanks
> Eric (N7JYS) Marshall's Communications
>
>      On Sunday, October 20, 2019, 09:14:06 AM CDT, Eric Harrison via ARM-allstar <arm-allstar at hamvoip.org> wrote:
>  
>  Jeffery, I have not built any new allstar nodes recently but if i remember correctly all stock installsdefault to SSH port 22. I would plug an HDMI monitor and keyboard  into you rpi4 to confirm this in /etc/ssh. But after a install I always change this port for security reasons. Hope this helps.
>
> Eric (N7JYS) Marshall's Communications
>
>      On Sunday, October 20, 2019, 01:29:12 AM CDT, Jeffrey Reid via ARM-allstar <arm-allstar at hamvoip.org> wrote:
>  
>  Okay, this shouldn’t be that difficult, even for an OM that’s not computer savvy.  Did a clean write onto the SD card.  Checksum okay. Installed into Pi4.  Turn on and blinks dit-dit-dit-dah…The letter V I believe.  I try Putty and know that the ethernet IP connected to the Pi is .106 because I have another node (one of Mark’s nano-nodes).  Use port 222.  Keep getting connection timed out.  So I am stuck at the easy part…Jeez, what am I doing wrong.  I tried typing the IP into the Browser with no luck in getting a page that says TEST.
>
> The same cable is now back connected to my other node and working just fine, listening to the Insomniac Net.  Now, if I can only get to configure the new Pi4.  Any Ideas?
>
> Regards,
>
> Jeffrey
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org

_______________________________________________

ARM-allstar mailing list
ARM-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2/3 web page - http://hamvoip.org  


More information about the ARM-allstar mailing list