[arm-allstar] Hamvoip Update V1.5.3-56

[James Hause]

Thanks Doug for the quick response !
Again a big thanks to you and the team for all your work !!
Jim,
KF5LBT

On Sat, Jul 13, 2019 at 8:25 PM "Doug Crompton via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> James,
>
>  Yes, that is correct. We have a supermon simpleusb settings option in beta
> now. I suspect it could be released in a week or so. BTW it will be in the
> edit menu so like the configuration editor you can have two levels of login
> so only some users can have access to those options.
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>
> On Sat, Jul 13, 2019 at 9:15 PM "James Hause via ARM-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > Hi Doug,
> > I did do an update, and see that the simpleusb tune control now shows up
> > when I click on the configuration editor.
> > I assume to make use of this, I still need to wait for the supermon
> script
> > to be completed before it will work ?
> >
> >
> > On Tue, Jul 9, 2019 at 12:07 AM "Doug Crompton via ARM-allstar" <
> > arm-allstar at hamvoip.org> wrote:
> >
> > > The update that went out last night used a variable for the TX DSP
> level
> > > that had previously been released in a prior update set to a test level
> > of
> > > 500. This interfered with last nights update. This has been re-released
> > > tonight with a new variable name - txdsplvl  vs. the original
> txdsplevel
> > > which is no longer used. When you install this update the TX DSP Level
> > will
> > > be set to 999 or maximum level to start in simpleusb-tune-menu. This
> will
> > > NOT effect any of your current settings. I am repeating last nights
> > message
> > > below for reference. The TX DSP level setting is only intended to lower
> > the
> > > level (values of 999 or less) after coarse setting the mixer level. In
> > most
> > > cases unless you need a fine setting the DSP level can be left at 999
> and
> > > as always use the TX mixer level to set the TX level. More info in the
> > > message below.
> > >
> > > -----------------------------------------------------------
> > > From last night.....
> > >
> > > There is an update out tonight which updates the simpleusb-tune-menu
> > > script, the chan_simpleusb.so channel driver and corrects some minor
> > mostly
> > > display issues in supermon, lsnodes, and IRLP. Users should update
> using
> > > the ADMIN menu item 1.  IRLP users should update to improve file
> loading
> > > reliability at boot.
> > >
> > > A new parameter has been added to the simpleusb-tune-menu script called
> > > Transmit DSP Level. this level allows fine adjustment of the TX levels
> of
> > > your FOB if necessary. Most users will not need to use it or set it. By
> > > default it is set to 999 and finely adjusts the TX level DOWN. So if
> you
> > do
> > > use it you would set the actual mixer level to a level a few steps
> higher
> > > than required and then fine adjust by reducing the DSP level down from
> > 999.
> > > While it can be set lower the DSP level should be kept in the 800 to
> 999
> > > range. Users of the CM119B chip could find the DSP setting more useful
> as
> > > the mixer range of the B chip is much coarser than prior chips. This
> > would
> > > mostly be confined to repeaters where you are using a service monitor
> to
> > > make more accurate adjustments. Always set the mixer level first and
> use
> > > the DSP level to lower the gain.If not using the DSP level leave it set
> > to
> > > 999. Note that the DSP level changes BOTH TXA and TXB channels equally.
> > >
> > > Note that a few lines in simpleusb-tune-menu have been integrated into
> > one
> > > line to reduce the number of total lines to not exceed displayable
> lines
> > on
> > > certain displays.
> > >
> > > In addition the chan_simpleusb.so module has been enhanced to provide
> for
> > > the setting and reading using json of all configuration values. This
> will
> > > be used in a supermon script allowing you to configure simpleusb
> > > graphically. The updated supermon code to do this is currently in beta
> > and
> > > will be released soon.
> > >
> > > Files updated include:
> > >
> > > Supermon web files updated:
> > >
> > > ast_reload.php
> > > astlookup.php
> > > fastrestart.php
> > > header.inc
> > > index.php
> > > link.php
> > > nodeinfo.inc
> > > reboot.php
> > > server.php
> > > stats.php
> > > configeditor.php
> > >
> > > IRLP files updated (if IRLP installed) :
> > >
> > > custom.crons
> > > loadcalls
> > > rc.irlp
> > > call
> > > statupdate
> > >
> > >
> > > *73 Doug*
> > >
> > > *WA3DSP*
> > >
> > > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> > > _______________________________________________
> > >
> > > ARM-allstar mailing list
> > > ARM-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > >
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>