[arm-allstar] Hamvoip Update V1.5.3-56

[James Hause]

Hi Doug,
I did do an update, and see that the simpleusb tune control now shows up
when I click on the configuration editor.
I assume to make use of this, I still need to wait for the supermon script
to be completed before it will work ?


On Tue, Jul 9, 2019 at 12:07 AM "Doug Crompton via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> The update that went out last night used a variable for the TX DSP level
> that had previously been released in a prior update set to a test level of
> 500. This interfered with last nights update. This has been re-released
> tonight with a new variable name - txdsplvl  vs. the original txdsplevel
> which is no longer used. When you install this update the TX DSP Level will
> be set to 999 or maximum level to start in simpleusb-tune-menu. This will
> NOT effect any of your current settings. I am repeating last nights message
> below for reference. The TX DSP level setting is only intended to lower the
> level (values of 999 or less) after coarse setting the mixer level. In most
> cases unless you need a fine setting the DSP level can be left at 999 and
> as always use the TX mixer level to set the TX level. More info in the
> message below.
>
> -----------------------------------------------------------
> From last night.....
>
> There is an update out tonight which updates the simpleusb-tune-menu
> script, the chan_simpleusb.so channel driver and corrects some minor mostly
> display issues in supermon, lsnodes, and IRLP. Users should update using
> the ADMIN menu item 1.  IRLP users should update to improve file loading
> reliability at boot.
>
> A new parameter has been added to the simpleusb-tune-menu script called
> Transmit DSP Level. this level allows fine adjustment of the TX levels of
> your FOB if necessary. Most users will not need to use it or set it. By
> default it is set to 999 and finely adjusts the TX level DOWN. So if you do
> use it you would set the actual mixer level to a level a few steps higher
> than required and then fine adjust by reducing the DSP level down from 999.
> While it can be set lower the DSP level should be kept in the 800 to 999
> range. Users of the CM119B chip could find the DSP setting more useful as
> the mixer range of the B chip is much coarser than prior chips. This would
> mostly be confined to repeaters where you are using a service monitor to
> make more accurate adjustments. Always set the mixer level first and use
> the DSP level to lower the gain.If not using the DSP level leave it set to
> 999. Note that the DSP level changes BOTH TXA and TXB channels equally.
>
> Note that a few lines in simpleusb-tune-menu have been integrated into one
> line to reduce the number of total lines to not exceed displayable lines on
> certain displays.
>
> In addition the chan_simpleusb.so module has been enhanced to provide for
> the setting and reading using json of all configuration values. This will
> be used in a supermon script allowing you to configure simpleusb
> graphically. The updated supermon code to do this is currently in beta and
> will be released soon.
>
> Files updated include:
>
> Supermon web files updated:
>
> ast_reload.php
> astlookup.php
> fastrestart.php
> header.inc
> index.php
> link.php
> nodeinfo.inc
> reboot.php
> server.php
> stats.php
> configeditor.php
>
> IRLP files updated (if IRLP installed) :
>
> custom.crons
> loadcalls
> rc.irlp
> call
> statupdate
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>