[arm-allstar] Transmit PL on Simple USB

[john at qso.com]

I just re-read my post and it sounded a little confusing, so I'll re-write.
My repeater does send PL on transmit, and my HT that I use to talk on my repeater has receive PL working. My Quantar controller emits a very strong birdie on the transmit frequency, a signal that my RF squelch won't mute on my HT at any setting. Only PL squelch works. However, PL mute still takes 1.5 seconds, making me listen to annoying digital noise for that time every time my repeater unkeys. Thus I'd like to set my PL to drop 1.5 seconds before the carrier.  Hope that makes it clearer, and PL from the Pi would make this easy.

-----Original Message-----
From: ARM-allstar <arm-allstar-bounces at hamvoip.org> On Behalf Of "John Griffith via ARM-allstar"
Sent: Friday, April 19, 2019 9:01 AM
To: 'ARM Allstar' <arm-allstar at hamvoip.org>
Cc: john at qso.com
Subject: Re: [arm-allstar] Transmit PL on Simple USB

Thank you for your replies.

My repeater controller emits a rather strong birdie on my transmit frequency.  My HT finally mutes 1.5 seconds after PL drops, but birdie is too strong to squelch at any setting. Dropping PL upon PTT release while setting repeater hang time to 1.5 seconds would be ideal. Generating the PL on the Pi and increasing the hang time on the Quantar was my plan.

John 
N7OKN


-----Original Message-----
From: ARM-allstar <arm-allstar-bounces at hamvoip.org> On Behalf Of "Chris via ARM-allstar"
Sent: Friday, April 19, 2019 2:10 AM
To: ARM Allstar <arm-allstar at hamvoip.org>
Cc: Chris <chood73 at yahoo.com>
Subject: Re: [arm-allstar] Transmit PL on Simple USB

If you have an older radio that doesn’t do tone get you a TS64 board and it will encode and decode for you.
It just goes in the audio chain. They work great!
Here is a link.
https://www.wiscointl.com/CSpecialists/ctcss.htm

> On Apr 18, 2019, at 11:15 PM, Doug Crompton via ARM-allstar <arm-allstar at hamvoip.org> wrote:
> 
> John,
> 
> No simpleusb does not provide PL tones. What are you using that 
> requires it? I suspect an older radio that does not have PL?  For 
> Allstar you really need RX PL or tone squelch. Out going PL would be 
> optional but is usually always there in radios when you engage incoming PL.
> 
> 
> *73 Doug*
> 
> *WA3DSP*
> 
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> 
> On Thu, Apr 18, 2019 at 11:12 PM "John Griffith via ARM-allstar" < 
> arm-allstar at hamvoip.org> wrote:
> 
>> Hey everyone,
>> Is there a way to provide a CTCSS tone on the transmitted carrier If 
>> I'm using the Simple USB channel?
>> 
>> John Griffith
>> N7OKN
>> 
>> _______________________________________________
>> 
>> ARM-allstar mailing list
>> ARM-allstar at hamvoip.org
>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>> 
>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>> 
> _______________________________________________
> 
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> 
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
_______________________________________________

ARM-allstar mailing list
ARM-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2/3 web page - http://hamvoip.org

_______________________________________________

ARM-allstar mailing list
ARM-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2/3 web page - http://hamvoip.org