[arm-allstar] Very low audio.

[Doug Crompton]

This is all very interesting but I do not believe it is a wide/narrow issue
as George is still modifying and shipping these radio right now.

Please try the DMK-URI Pin 9 as I described in the last email.

Also a note to all. The DMK-URI while a good card is WAY over priced at
this point. They have also switch over to a CM119B and apparently have not
adjusted values to match its different levels. For those two reasons I
would not recommend buying a DMK-URI at this point.


*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*


On Mon, Apr 1, 2019 at 7:06 PM "B Harvey via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> Fred,
>
>    I just ran through this very setup and suffered the same problem.
> Although many suggestions were given, nothing worked. It was suggested,
> that perhaps the radio will not function in wide band mode and I'm inclined
> to believe that is the case. I can assume that it worked for the person who
> developed the "How To" on the Hamvoip website but perhaps they had a
> different revision of the UV 82 radio. I even went so far as to remove the
> 4.7Kohm resistor in line with the receive line of the URI but it didn't
> help. I could never even reach the 3khz mark on the deviation test menu
> page. I'm now in the process of building a radioless node just to test my
> URI since I have the parts on hand. If that works, I'll go a different
> route with a radio. In all likelihood I'll use an Alinco DR 435 as this one
> is know to work well and not suffer long term ill effects. You posting with
> this problem almost makes me think I'm getting played the "April Fool"
>
>
> Brian / KK6DOQ
>
> On Mon, Apr 1, 2019 at 3:49 PM "Fred C. via ARM-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> >
> > Hi everyone,
> >
> > I am new to AllStar and new to that mailing list and I might ask a
> > question that has been answered server time. I haven’t found the answer
> to
> > my problem tho.
> >
> > I have installed hamvoip, on a Raspberry Pi 3B+, I am using the URI made
> > by DMK Engineering and a Baofeng UV-82, with the mods found on the
> hamvoip
> > website. Everything seems to be working ok besides my low, very low
> audio.
> > People I am talking with can barely hear me. On the receive everything is
> > fine.
> >
> > I have tried all the obvious things I could find on the internet, but
> > nothing seems to be working. I have played with simple_usb_tune. The RX
> > Boost Mode is on (1), my Rx Voice Level is set to 999. I have checked the
> > alsamixer and the microphone input is all the way up. I have even try to
> > remove the 4.7kΩ resistor on the DB25 connector and don’t get any
> > improvements.
> >
> > I was wondering if someone had encountered this problem before or if
> > something had an idea that I haven’t explored yet.
> >
> > 73,
> >
> > -fred-
> >
> > --
> > Fred C. (070 #2569)
> > w6bsd at bsdworld.org <mailto:w6bsd at bsdworld.org>
> https://www.qrz.com/db/W6BSD
> > <https://www.qrz.com/db/W6BSD>
> >
> >
> >
> >
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org