[arm-allstar] Supermon stopped working after re-start

[Ron Gilson]

Good morning Doug.  41893 is wired, LEDs flashing, ip is correct when
announcing (192.168.1.24), Tried a new chip with new image same problem.
DTMF connected to 28258 same LAN connected to 27225, all seems ok ?
Switched eithernet cables and ports on switch, re-boot router. still can't
talk to port .1.24?  Could it be I locked myself out when turning on
firewall.  The only thing I have not tried replacing the pie?  Any ideas
???  Thanks.
Ron

On Sun, Mar 31, 2019 at 6:18 PM Doug Crompton <wa3dsp at gmail.com> wrote:

> Ron,
>
>  Is this a wired or wireless connection. Does it announce an IP address
> when it boots? Does it show it on the LED's?
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>
> On Sun, Mar 31, 2019 at 6:13 PM Ron Gilson <wa2wwk at gmail.com> wrote:
>
>> Also, I believe I turned on the hamvoip firewall, but everything seemed
>> ok until the node powered up after plugging into the UPS?  I did the proper
>> shut down from putty?  Just checked and still at same LAN IP address???
>> Thanks.
>> WA2WWK
>>
>> On Sun, Mar 31, 2019 at 5:53 PM Ron Gilson <wa2wwk at gmail.com> wrote:
>>
>>> Thanks will check in am but the node looked like it stayed at .24.
>>> Enjoy the balance of the weekend.  73's
>>> Ron  WA2WWK
>>>
>>> On Sat, Mar 30, 2019 at 6:35 PM "Doug Crompton via ARM-allstar" <
>>> arm-allstar at hamvoip.org> wrote:
>>>
>>>> Ron,
>>>>
>>>>  If you didn't turn it off the node announces its IP address at boot.
>>>> The
>>>> IP address is also sent in morse code to the Pi LED twice at boot
>>>> preceded
>>>> by HI HI. I suspect your IP address changed if you are using DHCP and
>>>> you
>>>> did not make it reserved or permanent in your router.
>>>>
>>>>
>>>> *73 Doug*
>>>>
>>>> *WA3DSP*
>>>>
>>>> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>>>>
>>>> On Sat, Mar 30, 2019 at 6:23 PM "Ron Gilson via ARM-allstar" <
>>>> arm-allstar at hamvoip.org> wrote:
>>>>
>>>> > I recently set up Supermon on Node 41893.  Things seemed to work very
>>>> well
>>>> > until earlier today when I decided to shut down via putty so I could
>>>> > re-route power thru a ups backup.  After that the Supermon would no
>>>> longer
>>>> > work , putty and WinScp also could not access the node.  I looked on
>>>> my
>>>> > router and the IP is correct but I'm not able to ping 41893 from my
>>>> LAN.  I
>>>> > can dial up a connection to 27225 & and DTMF for ID, Time etc work
>>>> well.
>>>> > Any ideas other than start over again?  My other node on same LAN
>>>> different
>>>> > LAN IP has no problem?  Thanks for your help.
>>>> > WA2WWK  Ron
>>>> > _______________________________________________
>>>> >
>>>> > ARM-allstar mailing list
>>>> > ARM-allstar at hamvoip.org
>>>> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>> >
>>>> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>>> >
>>>> _______________________________________________
>>>>
>>>> ARM-allstar mailing list
>>>> ARM-allstar at hamvoip.org
>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>
>>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>>>
>>>