[arm-allstar] Supermon manager error

[Doug Crompton]

Rory,

 Did you read my email?

Are the 48089 and 48135 nodes on the server you are running supermon on? If
so why are you using the 70.x.x.x addresses in the allmon.ini file? They
should be 127.0.0.1  - which is the host they are on or localhost.

Also if that is the case you do not change the bindaddr in manager.conf. It
should either be 127.0.0.1 on the same server as the nodes you are managing
or 0.0.0.0 on nodes you are managing that are not on the same server that
supermon is running on.

Bottom line is if everything is on one server you always use 127.0.0.1:5038
in allmon.ini and  127.0.0.1 in the manager.

I thought this was clear in my email and the howto.


*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*


On Fri, May 11, 2018 at 11:18 AM, "Rory Bowers via arm-allstar" <
arm-allstar at hamvoip.org> wrote:

> Thanks Doug,
> Here is my allmon.ini...
>
> [48089]
> host=70.178.132.224:5038
> user=admin
> passwd=(my password)
> menu=yes
> hideNodeURL=no
> [48135]
> host=70.178.132.224:5038
> user=admin
> passwd=(my password again)
> menu=yes
> hideNodeURL=no
>
>
> [All Nodes]
> nodes=48089, 48135
> menu=yes
>
> [lsNodes]
> url="/cgi-bin/lsnodes_web?node=48089"
> menu=yes
>
> [IRLP Status]
> url="http://status.irlp.net"
> menu=yes
>
> [HAMVOIP]
> url="http://HamVOIP.org"
> menu=yes
>
> Here is where I get a little fuzzy... my manager.conf file
>
> [general]
>
> displaysystemname = yes
>
> enabled = yes
>
> webenabled = yes
>
> port = 5038
>
>
>
> httptimeout = 60
>
> ; a) httptimeout sets the Max-Age of the http cookie
>
> ; b) httptimeout is the amount of time the webserver waits
>
> ;    on a action=waitevent request (actually its httptimeout-10)
>
> ; c) httptimeout is also the amount of time the webserver keeps
>
> ;    a http session alive after completing a successful action
>
>
>
> bindaddr = 192.168.0.2   ; Local interface only!
>
> ;bindaddr = 0.0.0.0    ; Not secure
> ;
> displayconnects = yes
>
> ;
>
> ; Add a Unix epoch timestamp to events (not action responses)
>
> ;
>
> timestampevents = yes
>
>
>
> [admin]
>
> secret = (my password again)
>
> read = all,system,call,log,verbose,command,agent,user,config
>
> write = all,system,call,log,verbose,command,agent,user,config
>
> The bindaddr is set to the lan ip address of the Pi... not the Public ip
> address.  Is this correct??
>
> Rory, K5CKS
>
> On Fri, May 11, 2018 at 8:43 AM, "Doug Crompton via arm-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > Rory,
> >
> >  The message about the Supermon error did not go out because it had a
> > graphics file in it. So I am answering without your original message.
> >
> > If you cannot connect to the manager it is usually a problem with
> > authentication. You allmon.ini file must have a stanza or stanza's that
> > contain the nodes you want to view and a user/pass to the manager. Here
> is
> > an example:
> >
> > [40000]
> > host=127.0.0.1:5038
> > user=admin
> > passwd=managerpass
> > menu=yes
> > hideNodeURL=no
> >
> > The /etc/asterisk/manager.conf file credentials must match this -
> >
> > [admin]
> >
> > secret = managerpass
> >
> > In both places change the password to one of your choice. They MUST
> match!
> >
> > In addition if you are trying to manager a node on a different server the
> > host address in that stanza must be the IP address of that server and
> very
> > important the bindaddress must be changed in not on that server.
> >
> > bindaddr = 127.0.0.1   ; Local interface
> > only!
> > ;bindaddr = 0.0.0.0    ; Not secure
> >
> > The above would be correct for nodes on the server you are running
> Supermon
> > on but if you are trying to manage a node on another server you would
> need
> > to comment out the 127.0.0.1 address and un-comment the 0,0,0,0 address.
> If
> > the server address you were managing was out on the Internet then in
> > addition you would need to port forward the manager port and also
> institute
> > a firewall rule.
> >
> > All of this is covered in the howto found on the hamvoip.org web page.
> >
> >
> > *73 Doug*
> >
> > *WA3DSP*
> >
> > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>