[arm-allstar] Supermon manager error

[Rory Bowers]

Thanks Doug,
Here is my allmon.ini...

[48089]
host=70.178.132.224:5038
user=admin
passwd=(my password)
menu=yes
hideNodeURL=no
[48135]
host=70.178.132.224:5038
user=admin
passwd=(my password again)
menu=yes
hideNodeURL=no


[All Nodes]
nodes=48089, 48135
menu=yes

[lsNodes]
url="/cgi-bin/lsnodes_web?node=48089"
menu=yes

[IRLP Status]
url="http://status.irlp.net"
menu=yes

[HAMVOIP]
url="http://HamVOIP.org"
menu=yes

Here is where I get a little fuzzy... my manager.conf file

[general]

displaysystemname = yes

enabled = yes

webenabled = yes

port = 5038



httptimeout = 60

; a) httptimeout sets the Max-Age of the http cookie

; b) httptimeout is the amount of time the webserver waits

;    on a action=waitevent request (actually its httptimeout-10)

; c) httptimeout is also the amount of time the webserver keeps

;    a http session alive after completing a successful action



bindaddr = 192.168.0.2   ; Local interface only!

;bindaddr = 0.0.0.0    ; Not secure
;
displayconnects = yes

;

; Add a Unix epoch timestamp to events (not action responses)

;

timestampevents = yes



[admin]

secret = (my password again)

read = all,system,call,log,verbose,command,agent,user,config

write = all,system,call,log,verbose,command,agent,user,config

The bindaddr is set to the lan ip address of the Pi... not the Public ip
address.  Is this correct??

Rory, K5CKS

On Fri, May 11, 2018 at 8:43 AM, "Doug Crompton via arm-allstar" <
arm-allstar at hamvoip.org> wrote:

> Rory,
>
>  The message about the Supermon error did not go out because it had a
> graphics file in it. So I am answering without your original message.
>
> If you cannot connect to the manager it is usually a problem with
> authentication. You allmon.ini file must have a stanza or stanza's that
> contain the nodes you want to view and a user/pass to the manager. Here is
> an example:
>
> [40000]
> host=127.0.0.1:5038
> user=admin
> passwd=managerpass
> menu=yes
> hideNodeURL=no
>
> The /etc/asterisk/manager.conf file credentials must match this -
>
> [admin]
>
> secret = managerpass
>
> In both places change the password to one of your choice. They MUST match!
>
> In addition if you are trying to manager a node on a different server the
> host address in that stanza must be the IP address of that server and very
> important the bindaddress must be changed in not on that server.
>
> bindaddr = 127.0.0.1   ; Local interface
> only!
> ;bindaddr = 0.0.0.0    ; Not secure
>
> The above would be correct for nodes on the server you are running Supermon
> on but if you are trying to manage a node on another server you would need
> to comment out the 127.0.0.1 address and un-comment the 0,0,0,0 address. If
> the server address you were managing was out on the Internet then in
> addition you would need to port forward the manager port and also institute
> a firewall rule.
>
> All of this is covered in the howto found on the hamvoip.org web page.
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>