[arm-allstar] AllStar/IRLP

[wb9rsq at gmail.com]

Somehow I must have missed something important.
Is there a "how to" for adding IRLP node to allstar?
I know there was talk about code updates but I never noticed any actual release with instructions.
I'd love to get my node working again.
tnx


-----Original Message-----
From: arm-allstar <arm-allstar-bounces at hamvoip.org> On Behalf Of "Doug Crompton via arm-allstar"
Sent: Wednesday, May 9, 2018 4:34 PM
To: ARM Allstar <arm-allstar at hamvoip.org>
Cc: Doug Crompton <wa3dsp at gmail.com>
Subject: Re: [arm-allstar] AllStar/IRLP

The answer is yes, IRLP and Allstar/Echolink can be bridged (connected
together) based on the restrictions of the protocol. In the case of IRLP
only one connection in or out to many on Allstar and Echolink. This of
course assumes you have IRLP installed and a valid IRLP node setup.


*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*




On Wed, May 9, 2018 at 4:06 PM, "Ronald Foster via arm-allstar" <
arm-allstar at hamvoip.org> wrote:

> Doug, I may not have made myself clear.
>
> I’m wondering about connecting at the same time. Not independently of each
> other. As I commented, AllStar and IRLP were linked at the same time.
>
> How can each mode work at the same time, if they share a single HT/Pi?
>
> Understand?
>
> Thanks Doug.
>
> Ron
> > On May 9, 2018, at 1:58 PM, Doug Crompton via arm-allstar <
> arm-allstar at hamvoip.org> wrote:
> >
> > Ron,
> >
> > You can only connect to one IRLP node or reflector at a time but you can
> > have many nodes connected on the Allstar side. Incoming IRLP would
> connect
> > as long as no other IRLP is connected. The number of Allstar connects has
> > no bearing on it.
> >
> >
> > *73 Doug*
> >
> > *WA3DSP*
> >
> > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> >
> >
> > On Wed, May 9, 2018 at 8:12 AM, "Ronald E Foster via arm-allstar" <
> > arm-allstar at hamvoip.org> wrote:
> >
> >> I’m curious about the AllStar-IRLP modes running together.
> >>
> >> The other day, I mistakenly linked to an IRLP node while linked to an
> >> AllStar node. I immediately dropped the IRLP connection before using it,
> >> but now I’m curious how that would have impacted the modes while both
> were
> >> linked through my node.
> >>
> >> I’m also curious about an IRLP node connecting to my AllStar IRLP node.
> >> Would a traditional IRLP node receive a busy when requesting a link, if
> I
> >> were already linked to say... 27225 monitoring the hub or would my node
> >> need to be idle in both modes?
> >>
> >> Thanks for any enlightening on this topic.
> >>
> >> Ron, K0AAJ
> >> AllStar 42545
> >> IRLP 4100
> >> _______________________________________________
> >>
> >> arm-allstar mailing list
> >> arm-allstar at hamvoip.org
> >> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>
> >> Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
_______________________________________________

arm-allstar mailing list
arm-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2/3 web page - http://hamvoip.org