[arm-allstar] Hamvoip Shutdown Script

[Sean McCarthy]

It appears to be running with no errors, so that part seems to be working.
Long story short, a friend was dinking around trying to get the PI Uptime
UPS script working and I was not sure if he messed with the Hamvoip script.
Apparently not. Will not be able to physically visit the site to test until
Monday, hence the desire to see it running remotely.

As always, thanks Doug.
Sean

On Fri, Jul 13, 2018 at 3:30 PM, "Doug Crompton via arm-allstar" <
arm-allstar at hamvoip.org> wrote:

> ps ax | grep shutdown
>
> It should show a job. If you activated it in /usr/local/etc/allstar.env it
> should be there but only after a reboot.  Remember if you shut something
> down remotely it will not restart unless you cycle power.
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>
>
>
> On Fri, Jul 13, 2018 at 3:26 PM, "Sean McCarthy via arm-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > Right. How can I check if the script is running without simulating a
> power
> > loss?
> >
> > On Fri, Jul 13, 2018 at 3:20 PM, "Doug Crompton via arm-allstar" <
> > arm-allstar at hamvoip.org> wrote:
> >
> > > Sean,
> > >
> > >  The shutdown_monitor script is intended to work with the GPIO bit to
> > > signal shutdown. All you have to do is pull the pwr_good pin, defined
> as
> > > wiringpi pin 1 actual physical pin 11, low for about 5 seconds and it
> > will
> > > enter the shutdown state
> > >
> > > This is discussed in two howto on the hamvoip.org web page
> > >
> > > https://hamvoip.org/hamradio/power_shutdown_monitor/
> > >
> > > https://hamvoip.org/hamradio/RPi2_halt_switch/
> > >
> > > The shutdown_monitor is designed to work with the power shutdown board
> > but
> > > will work with any outside source that lower that pin at power failure.
> > The
> > > shutdown board uses a small battery to power the Pi during the shutdown
> > > process which takes about 15 seconds.
> > >
> > >
> > > *73 Doug*
> > >
> > > *WA3DSP*
> > >
> > > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> > >
> > >
> > >
> > > On Fri, Jul 13, 2018 at 2:44 PM, "Sean McCarthy via arm-allstar" <
> > > arm-allstar at hamvoip.org> wrote:
> > >
> > > > Besides simulating a power loss, how can I verify the shutdown script
> > is
> > > > running?
> > > >
> > > > I have "enabled" shutdown in allstar.env and rebooted.
> > > >
> > > > Thanks,
> > > > Sean
> > > > _______________________________________________
> > > >
> > > > arm-allstar mailing list
> > > > arm-allstar at hamvoip.org
> > > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > > >
> > > > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > > >
> > > _______________________________________________
> > >
> > > arm-allstar mailing list
> > > arm-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > >
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>