[arm-allstar] APRS
Luc Drolet VE2LUQ
ldrolet at cgocable.ca
Sun Aug 19 07:55:44 EDT 2018
BINGO,
I was using my website password to enter APRS and not the APRS generator code for operation
I did not know that we can have a generator code pass and the first time I hear that
a whole difference,
Thank you for your patience
Luc
VE2LUQ
> Le 19 août 2018 à 03:45, James R. Pilgram via arm-allstar <arm-allstar at hamvoip.org> a écrit :
>
> Maybe a dumb question on my part but did you use the correct password? I went to the passcode generator @ https://callpass.kf5jwc.us/
>
> Make sure it's correct. I followed the same link Doug just posted and have it working from last week with a GPS USB puck on my 27141 node. Not sure about hooking a radio to it on 144.390 though.
>
> Jim NH6HI
>
>
> On 08/18/2018 05:09 PM, "Doug Crompton via arm-allstar" wrote:
>> Luc,
>>
>> I searched back through some earlier emails and found this link which
>> might be helpful to you -
>>
>> http://n6jer.blogspot.com/2017/07/updating-aprs-with-allstar-node.html
>>
>>
>> *73 Doug*
>>
>> *WA3DSP*
>>
>> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>>
>>
>>
>> On Sat, Aug 18, 2018 at 9:05 PM, "Luc Drolet VE2LUQ via arm-allstar" <
>> arm-allstar at hamvoip.org> wrote:
>>
>>> Hello to you,
>>>
>>> I have one of my colleges tells me, that even you must have a radio to
>>> connect to your repeater with 144.39Mhz
>>>
>>> I thought my NODE 1400 145.130Mhz with its asterisk that everything was
>>> ok, only the configuration in Asterisk
>>> that I needed to add, as we did together:
>>>
>>> load = app_gps.so
>>> and add the gps.conf file
>>>
>>> ; Configuration for app_gps
>>> ;
>>> [general]
>>>
>>> call = ve2luq; callsign (including SSID) for APRS purposes
>>> password = xxxxxxxxx; Password for APRS-IS server
>>> comment = AllStar Node 1400; Text to be displayed with this station
>>> server = rotate.aprs2.net; APRS-IS server to report information
>>> port = 14580; port on server to send data
>>> interval = 600; Beacon interval in seconds
>>> icon = r; A CAR (default) Icon for the APRS display (see below)
>>> ; comport = / dev / ttyS0; Serial port for GPS receiver
>>> baudrate = 4800; Baud rate for GPS receiver
>>> ;debug = y; set this for debug output
>>> freq = 145.130; Display Frequency of station
>>> tone = 100.0; CTCSS tone of station (0.0 for none)
>>> lat = 46.1344359; Fixed latitude in decimal degrees
>>> lon = -71.2263340; Fixed (default) longitude in decimal degrees
>>> elev = 123.4; Elevation of Antenna in Meters (* NOT * HAAT)
>>> power = 1; Power level (see below)
>>> height = 2; Antenna Height in HAAT (see below)
>>> gain = 3; Antenna Gain (see below)
>>> dir = 0; Antenna Direction (see below)
>>>
>>> Luc
>>>
>>>> Le 18 août 2018 à 19:50, Luc Drolet VE2LUQ <ldrolet at cgocable.ca> a
>>> écrit :
>>>> Hi James,
>>>>
>>>> Yes I have good load = app_gps.so
>>>> but I do not see anything on the aprs.fi web page
>>>>
>>>> OK, I saw that you put a ";" at
>>>> ; behavior = / dev / ttyS0; Serial port for GPS receiver
>>>>
>>>> I'm going to try
>>>>
>>>> Luc
>>>>
>>>>
>>>>> Le 18 août 2018 à 19:03, James Hause via arm-allstar <
>>> arm-allstar at hamvoip.org> a écrit :
>>>>> Below is my gps.conf file Note lines in Red are commented out on mine.
>>>>> Hope this helps.
>>>>> ; Configuration for app_gps
>>>>> ;
>>>>> [general]
>>>>> call = KF5LBT-5 ; callsign (including SSID) for APRS purposes
>>>>> password = XXXXX ; Password for APRS-IS server for above callsign
>>>>> comment = AllStar Node 46738 ; Text to be displayed associated with this
>>>>> station
>>>>> server = rotate.aprs2.net ; APRS-IS server to report information to
>>>>> port = 14580 ; port on server to send data
>>>>> interval = 600 ; Beacon interval in seconds
>>>>> icon = r ; Antenna Icon do be displayed for station on APRS display
>>>>> ;comport = /dev/ttyS0 ; Serial port for GPS receiver (specify this only
>>> if
>>>>> using GPS receiver) Commented out
>>>>> ;baudrate = 4800 ; Baud rate for GPS receiver (specify this only if
>>> using
>>>>> GPS receiver) Commented out
>>>>> ;debug = y ; set this for debug output Commented out
>>>>> freq=147.465 ; Display Frequency of station
>>>>> tone=0.0 ; CTCSS tone of station (0.0 for none)
>>>>> lat=32.91425 ; Fixed (default) latitude in decimal degrees
>>>>> lon=-97.11686 ; Fixed (default) longitude in decimal degrees
>>>>> elev=180 ; Elevation of Antenna in Meters (*NOT* HAAT)
>>>>> power=0 ; Power level (see below)
>>>>> height=4 ; Antenna Height in HAAT (see below)
>>>>> gain=3 ; Antenna Gain (see below)
>>>>> dir=0 ; Antenna Direction (see below) Omni is 0
>>>>>
>>>>>
>>>>> For Modules:
>>>>>
>>>>> In the same /etc/asterisk directory, type nano modules.conf
>>>>> Scroll down 59 lines until you find:
>>>>> noload => app_gps.so ; GPS interface module
>>>>> Then simply delete the letters "no" so it looks like:
>>>>> load => app_gps.so ; GPS interface module
>>>>> Ctrl-x to save and exit.
>>>>>
>>>>> On Sat, Aug 18, 2018 at 5:39 PM, "Luc Drolet VE2LUQ via arm-allstar" <
>>>>> arm-allstar at hamvoip.org> wrote:
>>>>>
>>>>>> Hello James,
>>>>>>
>>>>>> I put
>>>>>>
>>>>>> load = app_gps.so
>>>>>> [global]
>>>>>>
>>>>>> and I waited 15 minutes to be sure to see on the web page aprs.fi if I
>>>>>> can see the repeater
>>>>>> and nothing is displayed
>>>>>>
>>>>>> Luc
>>>>>> VE2LUQ
>>>>>>
>>>>>>> Le 18 août 2018 à 18:10, James Hause via arm-allstar <
>>>>>> arm-allstar at hamvoip.org> a écrit :
>>>>>>> I think I see your problem. You need to change in MODULES.CONF
>>>>>> "noload =
>>>>>>> app_gps.so",
>>>>>>> to load=app.gps.so. Having the noload tells it no NOT load, you
>>> want
>>>>>> it
>>>>>>> to load.
>>>>>>>
>>>>>>> On Sat, Aug 18, 2018 at 4:21 PM, "Luc Drolet VE2LUQ via arm-allstar" <
>>>>>>> arm-allstar at hamvoip.org> wrote:
>>>>>>>
>>>>>>>> Hello to you,
>>>>>>>>
>>>>>>>> With asterisk I think we can have a tag placed on the APRS.FI site
>>> of
>>>>>> the
>>>>>>>> repeater position
>>>>>>>> I added the file using the ssh mode of the raspberry PI
>>>>>>>>
>>>>>>>> and I can not see my position on the APRS.FI website
>>>>>>>> in addition I also put in MODULES.CONF "noload = app_gps.so"
>>>>>>>>
>>>>>>>> ;——————————
>>>>>>>> ; Configuration for app_gps
>>>>>>>> ;
>>>>>>>> [general]
>>>>>>>>
>>>>>>>> call = ve2luq; callsign (including SSID) for APRS purposes
>>>>>>>> password = xxxxxxxxxxxx; Password for APRS-IS server
>>>>>>>> comment = AllStar Node 1400; Text to be displayed with this station
>>>>>>>> server = rotate.aprs2.net; APRS-IS server to report information
>>>>>>>> port = 14580; port on server to send data
>>>>>>>> interval = 600; Beacon interval in seconds
>>>>>>>> icon = r; A CAR (default) Icon for the APRS display (see below)
>>>>>>>> comport = / dev / ttyS0; Serial port for GPS receiver
>>>>>>>> baudrate = 4800; Baud rate for GPS receiver
>>>>>>>> debug = y; set this for debug output
>>>>>>>> freq = 145.130; Display Frequency of station
>>>>>>>> tone = 100.0; CTCSS tone of station (0.0 for none)
>>>>>>>> lat = 46.1344359; Fixed latitude in decimal degrees
>>>>>>>> lon = -71.2263340; Fixed (default) longitude in decimal degrees
>>>>>>>> elev = 123.4; Elevation of Antenna in Meters (* NOT * HAAT)
>>>>>>>> power = 1; Power level (see below)
>>>>>>>> height = 2; Antenna Height in HAAT (see below)
>>>>>>>> gain = 3; Antenna Gain (see below)
>>>>>>>> dir = 0; Antenna Direction (see below)
>>>>>>>> ;--------------------------
>>>>>>>>
>>>>>>>>
>>>>>>>> I can not see where my mistake is
>>>>>>>> I think it must work to see our position of our repeaters on the
>>>>>> APRS.FI
>>>>>>>> website
>>>>>>>>
>>>>>>>> Thank you and have a nice evening to you all
>>>>>>>>
>>>>>>>> Luc
>>>>>>>> VE2LUQ
>>>>>>>> _______________________________________________
>>>>>>>>
>>>>>>>> arm-allstar mailing list
>>>>>>>> arm-allstar at hamvoip.org
>>>>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>>>>>
>>>>>>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>>>>>> _______________________________________________
>>>>>>>
>>>>>>> arm-allstar mailing list
>>>>>>> arm-allstar at hamvoip.org
>>>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>>>>
>>>>>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>>>>> _______________________________________________
>>>>>>
>>>>>> arm-allstar mailing list
>>>>>> arm-allstar at hamvoip.org
>>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>>>
>>>>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>>>> _______________________________________________
>>>>>
>>>>> arm-allstar mailing list
>>>>> arm-allstar at hamvoip.org
>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>>
>>>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>> _______________________________________________
>>>
>>> arm-allstar mailing list
>>> arm-allstar at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>
>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>> _______________________________________________
>>
>> arm-allstar mailing list
>> arm-allstar at hamvoip.org
>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>
>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
More information about the arm-allstar
mailing list