[arm-allstar] APRS

Sat Aug 18 23:09:08 EDT 2018

Luc,

 I searched back through some earlier emails and found this link which
might be helpful to you -

http://n6jer.blogspot.com/2017/07/updating-aprs-with-allstar-node.html

*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*

On Sat, Aug 18, 2018 at 9:05 PM, "Luc Drolet VE2LUQ via arm-allstar" <
arm-allstar at hamvoip.org> wrote:

> Hello to you,
>
> I have one of my colleges tells me, that even you must have a radio to
> connect to your repeater with 144.39Mhz
>
> I thought my NODE 1400 145.130Mhz with its asterisk that everything was
> ok, only the configuration in Asterisk
> that I needed to add, as we did together:
>
> load = app_gps.so
> and add the gps.conf file
>
> ; Configuration for app_gps
> ;
> [general]
>
> call = ve2luq; callsign (including SSID) for APRS purposes
> password = xxxxxxxxx; Password for APRS-IS server
> comment = AllStar Node 1400; Text to be displayed with this station
> server = rotate.aprs2.net; APRS-IS server to report information
> port = 14580; port on server to send data
> interval = 600; Beacon interval in seconds
> icon = r; A CAR (default) Icon for the APRS display (see below)
> ; comport = / dev / ttyS0; Serial port for GPS receiver
> baudrate = 4800; Baud rate for GPS receiver
> ;debug = y; set this for debug output
> freq = 145.130; Display Frequency of station
> tone = 100.0; CTCSS tone of station (0.0 for none)
> lat = 46.1344359; Fixed latitude in decimal degrees
> lon = -71.2263340; Fixed (default) longitude in decimal degrees
> elev = 123.4; Elevation of Antenna in Meters (* NOT * HAAT)
> power = 1; Power level (see below)
> height = 2; Antenna Height in HAAT (see below)
> gain = 3; Antenna Gain (see below)
> dir = 0; Antenna Direction (see below)
>
> Luc
>
> > Le 18 août 2018 à 19:50, Luc Drolet VE2LUQ <ldrolet at cgocable.ca> a
> écrit :
> >
> > Hi James,
> >
> > Yes I have good load = app_gps.so
> > but I do not see anything on the aprs.fi web page
> >
> > OK, I saw that you put a ";" at
> > ; behavior = / dev / ttyS0; Serial port for GPS receiver
> >
> > I'm going to try
> >
> > Luc
> >
> >
> >> Le 18 août 2018 à 19:03, James Hause via arm-allstar <
> arm-allstar at hamvoip.org> a écrit :
> >>
> >> Below is my gps.conf file Note lines in Red are commented out on mine.
> >> Hope this helps.
> >> ; Configuration for app_gps
> >> ;
> >> [general]
> >> call = KF5LBT-5 ; callsign (including SSID) for APRS purposes
> >> password = XXXXX ; Password for APRS-IS server for above callsign
> >> comment = AllStar Node 46738 ; Text to be displayed associated with this
> >> station
> >> server = rotate.aprs2.net ; APRS-IS server to report information to
> >> port = 14580 ; port on server to send data
> >> interval = 600 ; Beacon interval in seconds
> >> icon = r ; Antenna Icon do be displayed for station on APRS display
> >> ;comport = /dev/ttyS0 ; Serial port for GPS receiver (specify this only
> if
> >> using GPS receiver) Commented out
> >> ;baudrate = 4800 ; Baud rate for GPS receiver (specify this only if
> using
> >> GPS receiver) Commented out
> >> ;debug = y ; set this for debug output Commented out
> >> freq=147.465 ; Display Frequency of station
> >> tone=0.0 ; CTCSS tone of station (0.0 for none)
> >> lat=32.91425 ; Fixed (default) latitude in decimal degrees
> >> lon=-97.11686 ; Fixed (default) longitude in decimal degrees
> >> elev=180 ; Elevation of Antenna in Meters (*NOT* HAAT)
> >> power=0 ; Power level (see below)
> >> height=4 ; Antenna Height in HAAT (see below)
> >> gain=3 ; Antenna Gain (see below)
> >> dir=0 ; Antenna Direction (see below) Omni is 0
> >>
> >>
> >> For Modules:
> >>
> >> In the same /etc/asterisk directory, type nano modules.conf
> >> Scroll down 59 lines until you find:
> >> noload => app_gps.so ; GPS interface module
> >> Then simply delete the letters "no" so it looks like:
> >> load => app_gps.so ; GPS interface module
> >> Ctrl-x to save and exit.
> >>
> >> On Sat, Aug 18, 2018 at 5:39 PM, "Luc Drolet VE2LUQ via arm-allstar" <
> >> arm-allstar at hamvoip.org> wrote:
> >>
> >>> Hello James,
> >>>
> >>> I put
> >>>
> >>> load = app_gps.so
> >>> [global]
> >>>
> >>> and I waited 15 minutes to be sure to see on the web page aprs.fi if I
> >>> can see the repeater
> >>> and nothing is displayed
> >>>
> >>> Luc
> >>> VE2LUQ
> >>>
> >>>> Le 18 août 2018 à 18:10, James Hause via arm-allstar <
> >>> arm-allstar at hamvoip.org> a écrit :
> >>>>
> >>>> I think I see your problem.  You need to change   in MODULES.CONF
> >>> "noload =
> >>>> app_gps.so",
> >>>> to load=app.gps.so.   Having the noload tells it no NOT load, you
> want
> >>> it
> >>>> to load.
> >>>>
> >>>> On Sat, Aug 18, 2018 at 4:21 PM, "Luc Drolet VE2LUQ via arm-allstar" <
> >>>> arm-allstar at hamvoip.org> wrote:
> >>>>
> >>>>> Hello to you,
> >>>>>
> >>>>> With asterisk I think we can have a tag placed on the APRS.FI site
> of
> >>> the
> >>>>> repeater position
> >>>>> I added the file using the ssh mode of the raspberry PI
> >>>>>
> >>>>> and I can not see my position on the APRS.FI website
> >>>>> in addition I also put in MODULES.CONF "noload = app_gps.so"
> >>>>>
> >>>>> ;——————————
> >>>>> ; Configuration for app_gps
> >>>>> ;
> >>>>> [general]
> >>>>>
> >>>>> call = ve2luq; callsign (including SSID) for APRS purposes
> >>>>> password = xxxxxxxxxxxx; Password for APRS-IS server
> >>>>> comment = AllStar Node 1400; Text to be displayed with this station
> >>>>> server = rotate.aprs2.net; APRS-IS server to report information
> >>>>> port = 14580; port on server to send data
> >>>>> interval = 600; Beacon interval in seconds
> >>>>> icon = r; A CAR (default) Icon for the APRS display (see below)
> >>>>> comport = / dev / ttyS0; Serial port for GPS receiver
> >>>>> baudrate = 4800; Baud rate for GPS receiver
> >>>>> debug = y; set this for debug output
> >>>>> freq = 145.130; Display Frequency of station
> >>>>> tone = 100.0; CTCSS tone of station (0.0 for none)
> >>>>> lat = 46.1344359; Fixed latitude in decimal degrees
> >>>>> lon = -71.2263340; Fixed (default) longitude in decimal degrees
> >>>>> elev = 123.4; Elevation of Antenna in Meters (* NOT * HAAT)
> >>>>> power = 1; Power level (see below)
> >>>>> height = 2; Antenna Height in HAAT (see below)
> >>>>> gain = 3; Antenna Gain (see below)
> >>>>> dir = 0; Antenna Direction (see below)
> >>>>> ;--------------------------
> >>>>>
> >>>>>
> >>>>> I can not see where my mistake is
> >>>>> I think it must work to see our position of our repeaters on the
> >>> APRS.FI
> >>>>> website
> >>>>>
> >>>>> Thank you and have a nice evening to you all
> >>>>>
> >>>>> Luc
> >>>>> VE2LUQ
> >>>>> _______________________________________________
> >>>>>
> >>>>> arm-allstar mailing list
> >>>>> arm-allstar at hamvoip.org
> >>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>>>>
> >>>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >>>> _______________________________________________
> >>>>
> >>>> arm-allstar mailing list
> >>>> arm-allstar at hamvoip.org
> >>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>>>
> >>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >>>
> >>> _______________________________________________
> >>>
> >>> arm-allstar mailing list
> >>> arm-allstar at hamvoip.org
> >>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>>
> >>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >> _______________________________________________
> >>
> >> arm-allstar mailing list
> >> arm-allstar at hamvoip.org
> >> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >>
> >> Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
>
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org