[arm-allstar] How difficult would it be to add dpl to the repeater controller of this distro?

[Sam Skolfield]

How do we know he isn't dealing with an MTR2000?
On Sun, May 21, 2017 at 2:21 PM "Pierre Martel via arm-allstar" <
arm-allstar at hamvoip.org> wrote:

> On a MSR2000 that have an external controler you need to make sure that the
> internal audio lines are not in parallel to the controler audio lines, only
> one line should sent to the xmitter. one way to test if the inetrnal system
> feed the exciter as well as the allstar controler, disconnect the wire that
> come OUT of the audio section of your USB card. Dont know if you use a URI
> or moded usb fob. but on the URI it would be the pins 10-11 or 22-23 both
> have the same AC audio level. one is dc coupled the other are AC coupled.
> they are the LEFT and RIGHT signal that comes OUT of the audio fob or URI
>
> 2017-05-21 14:22 GMT-04:00 "Clint (WB3EHB) via arm-allstar" <
> arm-allstar at hamvoip.org>:
>
> > To better answer you question, you will need in your hands the MSR 2000
> > BASE & REPEATER CONTROLAND AUDIO MANUAL(68P81061E40-C(
> > repeater-builder.com)).  Additionally you need the following card... if
> > simplex TRN4077A or for duplex operation TRN5076A, plus the associated
> DPL
> > code plugs one for Tx and one for RX.
> > If these parts are not available (which they may not be) then look to
> > adding a COMM-Spec board (DCS-23) to your MSR
> > Have fun
> >
> >
> > Clint WB3EHB
> >
> > DMR ID.. 3134022
> >
> > AllStar Node 27631
> >
> > IRLP Node's 3740 & 4546
> > WB3EHB at yahoo.com
> >
> > On Sunday, May 21, 2017, 12:17:19 PM EDT, Clint (WB3EHB) via arm-allstar
> <
> > arm-allstar at hamvoip.org> wrote:To add DPL to a MSR 2000 you will a
> Master
> > Decoder Card, and a DPL card dor the exciter and one for the receiver.
> puls
> > the DPL code plug for each
> >
> >
> > Clint WB3EHB
> >
> > DMR ID.. 3134022
> >
> > AllStar Node 27631
> >
> > IRLP Node's 3740 & 4546
> > WB3EHB at yahoo.com
> >
> > On Sunday, May 21, 2017, 4:35:37 AM EDT, kd4ont via arm-allstar <
> > arm-allstar at hamvoip.org> wrote:We are having problems with a Motorola
> > 2000, forgot the exact model, repeater uhf. With the node IDing in voice,
> > and controlling the rest, and the 2000 handling cw ID and other
> functions,
> > we have an issue of initial key up, doing a loud echo in analog pl, for a
> > fraction of a second, then the levels clamp down.
> > I'm guessing that it is two controllers fighting each other. It sounds
> > like the agc takes less than a second to clamp down on the levels.
> > We are close to deploying the hardware to the final building top but
> can't
> > nail down what is causing this.
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>
-- 
KJ6QFS
Sam Skolfield