[arm-allstar] DTMF Tones

[Larry]

Kerry,

Disregard my last message.  I looked up your node number and see you are 
not as new to Allstar as I first thought.
I tried connecting to your node 46740 It shows it is online but it 
replies the connection failed.

Since Doug has pointed you in the right direction I will just follow 
along reading to hear your solution.

73
Larry - N7FM


On 12/29/2017 10:17 PM, "Larry via arm-allstar" wrote:
> Kerry,
>
> Give the group a bit more detail about your situation...
>
> If you're new to Allstar there may be those who assume many people are 
> past the initial learning curve which isn't always the case.
>
> What version of Allstar are you running?
> Is the software the hamvoip version or Dial Version?
> How did you access your node to configure it? Using direct connections 
> to the Pi2 or a network connection on your local network?
> Since you mentioned control via a Web Interface what operating system 
> are you using? Linux or Windows?
> Are you currently able to login to the node and get to a command line 
> prompt?
> What is your node number?
>
> A little more info makes a difference in what people send on here to 
> assist you. Especially if you are new to all this.
>
> Larry - N7FM
> Node 29018
>
>
>
> On 12/29/2017 09:36 PM, "Larry via arm-allstar" wrote:
>> Kerry,
>>
>> If controlling means dialing a connection.... or sending commands? I 
>> must ask are you prefacing the dtmf tones you are sending with a "*" ?
>>
>> Like *3XXXXX to connect to a node in the tranceive mode. (Replace 
>> XXXXX with a node number)  or  send *81 for time playback?
>>
>> Larry - N7FM
>>
>> On 12/29/2017 09:08 PM, "Kerry McKenzie via arm-allstar" wrote:
>>> Hi All
>>> Have spent considerable time with little success I am unable to 
>>> control my
>>> node via DTMF Tones
>>> The configuration is raspberry pi2 with a DMK URLx controller 
>>> connected to
>>> a Hytera node radio model MD6652
>>> I am trying to figure if the tones are not being decoded in the 
>>> radio or in
>>> the node itself.
>>>
>>> I might be able to work around this if i new how to control the Pi 
>>> from the
>>> web inteface on the website but i can not
>>> find how to control the node this way either.
>>>
>>> I have tried sending tones from two icom radios, a Baofeng radio.
>>>
>>> Sorry cannot be more specific but the tone are passing through the node
>>> radio(Hytera) as i can hear them in the speaker.
>>> Are there any settings i may have missed or has anyone else experienced
>>> this and if so how did you remedy it.
>>> thanks Kerry VK4TUB
>>> _______________________________________________
>>>
>>> arm-allstar mailing list
>>> arm-allstar at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>
>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>>
>>
>> _______________________________________________
>>
>> arm-allstar mailing list
>> arm-allstar at hamvoip.org
>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>
>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org