[arm-allstar] Better audio?

[Chris Zenchenko]

I did play with the de and pre settings but noticed little change.
Not sure which mods you are referencing, we did build up the URI interface
and as indicated activated the onboard amp.
Currently the repeater is completely in remote mode with only the BBB doing
the lifting.
The audio sounds muddy and dull.
No high-end at all. Low-end rolled-off well above 300HZ.
I need sighted help so any re-wiring or changes on the DR1X screens depends
on when I can get it.
 
 
From: arm-allstar [mailto:arm-allstar-bounces at hamvoip.org] On Behalf Of Doug
Crompton via arm-allstar
Sent: Wednesday, April 20, 2016 8:46 AM
To: ARM Allstar <arm-allstar at hamvoip.org>
Cc: Doug Crompton <doug at crompton.com>
Subject: Re: [arm-allstar] Better audio?
 
Chris,

  I am very surprised that you are not getting good audio with the DR1X. We
have several repeaters in my area using Allstar with that repeater with
excellent audio. I assume you are using only analog FM on the repeater? Did
you follow the mods I published on hamvoip.org?

simpleusb has very good audio and most problems can be attributed to the
radio or settings. I believe the DR1 repeaters need both deemphasis and
pre-emphasis set to on. Make sure both are uncommented and set to yes. 

Exactly what is not right with the audio. Too many lows, highs, distorted?

73 Doug
WA3DSP
http://www.crompton.com/hamradio


  _____  

To: arm-allstar at hamvoip.org
Date: Wed, 20 Apr 2016 08:08:37 -0500
Subject: [arm-allstar] Better audio?
From: arm-allstar at hamvoip.org
CC: wb9rsq at gmail.com
Sorry about the length ahead of time.
I just moved my simplex node to a DR1X repeater and have started to
reconfigure much of my node.
Since I was using an older radio for the simplex operation I didn't pay much
attention to the audio quality.
However now as a repeater system under full allstar control I am quite
unhappy with the audio.
Some things I don't understand:
The differences and impact of the rx and tx parameters between the
simpleusb.conf and the simple_tune_usb.conf don't seem to be apparent.
I toggled the preemphasis parameter in simpleusb.conf but it didn't seem to
matter much.
We added the amp power to the URI and at least that increased the levels
enough to make the system usable but it also seemed to increase the
background noise level going to the TX while keyed even with no audio.
Is there a way to add some sort of eq?
What parameters would increase the input so that output could be dialed
back?
I'm including as input items for increase not only OTA audio but tones and
local audio and of course allstar audio from external connections.
I am running the DR1X with squelch open and the node is ignoring ctcss and
carrier detect. Can the allstar control get either of these signals from the
DR1X when allstar is the controller?
At the moment I've got quite a squelch tail!
I realize that I could go to the DR1X control mode or add some sort of other
external controller but I really wanted to have allstar be the only
controller in the mix.
Any help would be appreciated.

_______________________________________________ arm-allstar mailing list
arm-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar Visit the BBB
and RPi2 web page - http://hamvoip.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20160420/6f9ef730/attachment-0001.html>