<html><head></head><body><div style="color:#000; background-color:#fff; font-family:times new roman, new york, times, serif;font-size:16px"><div>Leroy,</div><div id="yui_3_16_0_ym19_1_1473883040924_167241"><br></div><div id="yui_3_16_0_ym19_1_1473883040924_167239">Please indicate whih pin you are using off of the transceiver interface (16 pin connection)???<br></div><div id="yui_3_16_0_ym19_1_1473883040924_167238"><span></span></div><div id="yui_3_16_0_ym19_1_1473883040924_167184"> </div><div id="yui_3_16_0_ym19_1_1473883040924_167168" class="signature"><font size="6"><span style="background-color:rgb(156, 0, 92);">Clint </span></font><pre class="moz-signature"><font size="5">WB3EHB</font>
DMR ID.. 3134022
AllStar Node 27631
IRLP Node's 3740 & 4546
</pre>
WB3EHB@yahoo.com</div> <div class="qtdSeparateBR"><br><br></div><div style="display: block;" class="yahoo_quoted"> <div style="font-family: times new roman, new york, times, serif; font-size: 16px;"> <div style="font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px;"> <div dir="ltr"><font face="Arial" size="2"> On Thursday, September 15, 2016 5:40 PM, LaRoy McCann via arm-allstar <arm-allstar@hamvoip.org> wrote:<br></font></div> <blockquote style="border-left: 2px solid rgb(16, 16, 255); margin-left: 5px; margin-top: 5px; padding-left: 5px;"> <br><br> <div class="y_msg_container"><br>I have a GR1225 repeater that I acquired. It was a functioning <br>standalone repeater.<br>I now have it connected to a Pi and working.<br><br>The audio from the radio sounds great but the issue is with the amount <br>of volume I am getting from the reciever.<br>I still peak over 5kc in simpleusb-tune-menu on loud voice peaks, and <br>that is with a Bofeng ht.<br><br>I have rxboost set to 0 in simpleusb.conf. I am down to 10 on the <br>receiver adjustment of simpleusb-tune-menu.<br>All this and the audio is still a little hot.<br><br>This is the first gr1225 I have played with. I am not sure about the <br>settings in the radio.<br>The Rx Audio Output is set to flat.<br>Operation Mode is set to Repeater w/Ext Controller.<br>Repeater Audio Mode is set to EIA.<br><br>There is a setting on the service menu, some type of gain setting (don't <br>remember exactly what it was called) that went from 0-31. This was set to 4.<br><br>Is there any other setting I am missing that would turn down the volume?<br>Is there any pot adjustment in the radio?<br><br>Do I need to add a resistor or pot in the audio line to adjust the level?<br><br><br>LaRoy McCann - K5TW<br><br><br><br>---<br>This email has been checked for viruses by Avast antivirus software.<br><a href="https://www.avast.com/antivirus" target="_blank">https://www.avast.com/antivirus</a><br><br>_______________________________________________<br><br>arm-allstar mailing list<br><a ymailto="mailto:arm-allstar@hamvoip.org" href="mailto:arm-allstar@hamvoip.org">arm-allstar@hamvoip.org</a><br><a href="http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar" target="_blank">http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar</a><br><br>Visit the BBB and RPi2 web page - <a href="http://hamvoip.org/" target="_blank">http://hamvoip.org</a><br><br><br></div> </blockquote> </div> </div> </div></div></body></html>