<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 12pt;
font-family:Calibri
}
--></style></head>
<body class='hmmessage'><div dir='ltr'><font style="" face="Tahoma,sans-serif" color="#000000">Laroy,<br><br> You say the radio has +10V unsquelched but you are not going to use that output if you use the Spec comm decoder right? Also the DMK URI uses blocking diodes in the input lines so it will accept higher input voltages they do not have to be TTL levels as long as the low is a good low, close to zero volts.<br><br>When you get it setup using just PL set the rxaudiodelay in simpleusb.conf to about 7 or 8 and see how the squelch tails sound listening on another node or iaxrpt monitoring it. Make sure that line is uncommented also. You can go up from there if needed. Restsart Asterisk - astres.sh - when yo make changes.<br id="FontBreak"></font><br><b><font style="font-size:16pt;" size="4">73 Doug</font><font style="font-size:16pt;" size="4"><br></font><font style="font-size:16pt;" size="4">WA3DSP</font><font style="font-size:16pt;" size="4"><br></font><font style="font-size:16pt;" size="4">http://www.crompton.com/hamradio</font></b><font style="font-size:16pt;" size="4"><br></font><br><br><div><hr id="stopSpelling">To: arm-allstar@hamvoip.org<br>Date: Fri, 13 May 2016 10:21:09 -0500<br>Subject: Re: [arm-allstar] Using PL instead of COS<br>From: arm-allstar@hamvoip.org<br>CC: lmccann@dtisp.com<br><br>
<div class="ecxmoz-cite-prefix">Doug,<br>
I said it will be wired directly to allstar but I am using the
URIx interface.<br>
<br>
LaRoy McCann, K5TW<br>
<br>
<br>
On 5/13/2016 10:06 AM, LaRoy McCann via arm-allstar wrote:<br>
</div>
<blockquote cite="mid:7cc7847f-4406-b9f0-e7ab-d0f0fdf451ae@dtisp.com">
<div class="ecxmoz-cite-prefix">Doug,<br>
There is no other controller. The exec II is a mobile radio
converted to a repeater. It will be controlled directly with
allstar. I curently have 2 repeaters running on allstar and
will soon have 3 or 4 more running on allstar.<br>
<br>
Allstar will switch direction (usb or usb invert) but since the
radio gives +10v when unsquelched, I will need to make a buffer
because the raspberry pi needs to see the input go to ground.<br>
<br>
The TS64 signal is an open collector to ground so it interfaces
well with allstar.<br>
<br>
LaRoy McCann, K5TW<br>
<br>
<br>
<br>
<br>
On 5/13/2016 9:47 AM, Doug Crompton via arm-allstar wrote:<br>
</div>
<blockquote cite="mid:BLU171-W101DD78BB9DB3A14DD0E08EBA740@phx.gbl">
<style><!--
.ExternalClass .ecxhmmessage P {
padding:0px;
}
.ExternalClass body.ecxhmmessage {
font-size:12pt;
font-family:Calibri;
}
--></style>
<div dir="ltr"><font style="" face="Tahoma,sans-serif" color="#000000">LaRoy<br id="ecxFontBreak">
</font><br>
I have never interfaced what you are talking about but I see
no reason why you would need the squelch input as well as PL.
The TS64 works well and the audio delay (squelch tail
elimination) setting in simpleusb.conf should get rid of any
squelch tail. <br>
<br>
I assume you are using a separate repeater controller and not
using Allstar as the controller? If you are using Allstar you
can configure the COS direction. Also I thought maybe the TS64
had both high and low going outputs but maybe not. <br>
<br>
Allstar makes a great repeater controller but there are some
pros and cons to using it. The big pro is that you don't have
to worry about physical ports like you do on a dedicated
controller. Each port is a node and can be configured and
connected easily via SW, a big plus for Allstar. It is also a
lot less expensive. <br>
<br>
<b><font style="font-size:16pt;" size="4">73 Doug</font><font style="font-size:16pt;" size="4"><br>
</font><font style="font-size:16pt;" size="4">WA3DSP</font><font style="font-size:16pt;" size="4"><br>
</font><font style="font-size:16pt;" size="4"><a class="ecxmoz-txt-link-freetext" href="http://www.crompton.com/hamradio" target="_blank"></a><a class="ecxmoz-txt-link-freetext" href="http://www.crompton.com/hamradio" target="_blank">http://www.crompton.com/hamradio</a></font></b><font style="font-size:16pt;" size="4"><br>
</font><br>
<br>
<div>> To: <a class="ecxmoz-txt-link-abbreviated" href="mailto:arm-allstar@hamvoip.org">arm-allstar@hamvoip.org</a><br>
> Date: Fri, 13 May 2016 09:32:27 -0500<br>
> Subject: [arm-allstar] Using PL instead of COS<br>
> From: <a class="ecxmoz-txt-link-abbreviated" href="mailto:arm-allstar@hamvoip.org">arm-allstar@hamvoip.org</a><br>
> CC: <a class="ecxmoz-txt-link-abbreviated" href="mailto:lmccann@dtisp.com">lmccann@dtisp.com</a><br>
> <br>
> I'm interfacing a ge mastr exec II to raspberry pi. I
have one I've <br>
> done previously where I have both cos and pl inputs.<br>
> <br>
> I'm going to have to make a cos buffer interface to
change the cos_high <br>
> from the radio to cos_low for the controller which is
no problem,<br>
> <br>
> We will always us PL on the input so I was wondering if
I could just get <br>
> by with using the TS64 PL signal for the cos input on
the controller?<br>
> <br>
> Does anyone know of any reasons not to use only PL
signal for cos?<br>
> <br>
> Would there be any longer squelch tail?<br>
> <br>
> <br>
> LaRoy McCann, K5TW<br>
> <br>
> <br>
> ---<br>
> This email has been checked for viruses by Avast
antivirus software.<br>
> <a class="ecxmoz-txt-link-freetext" href="https://www.avast.com/antivirus" target="_blank">https://www.avast.com/antivirus</a><br>
> <br>
> _______________________________________________<br>
> <br>
> arm-allstar mailing list<br>
> <a class="ecxmoz-txt-link-abbreviated" href="mailto:arm-allstar@hamvoip.org">arm-allstar@hamvoip.org</a><br>
> <a class="ecxmoz-txt-link-freetext" href="http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar" target="_blank">http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar</a><br>
> <br>
> Visit the BBB and RPi2 web page - <a class="ecxmoz-txt-link-freetext" href="http://hamvoip.org" target="_blank"></a><a class="ecxmoz-txt-link-freetext" href="http://hamvoip.org" target="_blank">http://hamvoip.org</a><br>
> <br>
</div>
</div>
<br>
-- <br>
This message has been scanned for viruses and <br>
dangerous content by the <a href="http://www.dtisp.com/" target="_blank"><b>DTISP MailScanner</b></a>, and
is <br>
believed to be clean. <br>
<fieldset class="ecxmimeAttachmentHeader"></fieldset>
<br>
<pre>_______________________________________________
arm-allstar mailing list
<a class="ecxmoz-txt-link-abbreviated" href="mailto:arm-allstar@hamvoip.org">arm-allstar@hamvoip.org</a>
<a class="ecxmoz-txt-link-freetext" href="http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar" target="_blank">http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar</a>
Visit the BBB and RPi2 web page - <a class="ecxmoz-txt-link-freetext" href="http://hamvoip.org" target="_blank">http://hamvoip.org</a></pre>
</blockquote>
<br>
<BR>
<br>
<table style="border-top:1px solid #aaabb6;">
<tbody>
<tr>
<td style="width:55px;padding-top:13px;"><a href="https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient&utm_term=icon" target="_blank"><img src="https://ipmcdn.avast.com/images/2016/icons/icon-envelope-tick-round-orange-v1.png"></a></td>
<td style="width:470px;padding-top:15px;color:#41424e;font-size:13px;font-family:Arial, Helvetica, sans-serif;line-height:18px;">Virus-free. <a href="https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient&utm_term=link" target="_blank" style="color:#4453ea;"></a><a class="ecxmoz-txt-link-abbreviated" href="http://www.avast.com" target="_blank">www.avast.com</a>
</td>
</tr>
</tbody>
</table>
<br>
-- <br>
This message has been scanned for viruses and
<br>
dangerous content by the
<a href="http://www.dtisp.com/" target="_blank"><b>DTISP
MailScanner</b></a>, and is
<br>
believed to be clean.
<br>
<fieldset class="ecxmimeAttachmentHeader"></fieldset>
<br>
<pre>_______________________________________________
arm-allstar mailing list
<a class="ecxmoz-txt-link-abbreviated" href="mailto:arm-allstar@hamvoip.org">arm-allstar@hamvoip.org</a>
<a class="ecxmoz-txt-link-freetext" href="http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar" target="_blank">http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar</a>
Visit the BBB and RPi2 web page - <a class="ecxmoz-txt-link-freetext" href="http://hamvoip.org" target="_blank">http://hamvoip.org</a></pre>
</blockquote>
<br>
<BR>
<br>
<table style="border-top:1px solid #aaabb6;">
<tbody><tr>
<td style="width:55px;padding-top:13px;"><a href="https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient&utm_term=icon" target="_blank"><img src="https://ipmcdn.avast.com/images/2016/icons/icon-envelope-tick-round-orange-v1.png"></a></td>
<td style="width:470px;padding-top:15px;color:#41424e;font-size:13px;font-family:Arial, Helvetica, sans-serif;line-height:18px;">Virus-free. <a href="https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient&utm_term=link" target="_blank" style="color:#4453ea;">www.avast.com</a>
</td>
</tr>
</tbody></table>
<br>_______________________________________________
arm-allstar mailing list
arm-allstar@hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
Visit the BBB and RPi2 web page - http://hamvoip.org</div> </div></body>
</html>