<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 12pt;
font-family:Calibri
}
--></style></head>
<body class='hmmessage'><div dir='ltr'><font style="" color="#000000" face="Tahoma,sans-serif">Joe,<br><br> The URI cos input is blocked by a diode with a very weak pullup on the CM119 chip. So the high level could be any reasonable voltage up to 20-30 volts but it would usually never be that high. Usually around 12, 5V, or 3V depending on the radios logic level. It does not really matter as it is blocked by the diode. The thing that matters is that low is really low - zero volts or there about.<br><br>You probably would not have to buffer as the URI pin 8 has very little load. I guess experimentation is in order. <br id="FontBreak"></font><br><b><font style="font-size:16pt;" size="4">73 Doug</font><font style="font-size:16pt;" size="4"><br></font><font style="font-size:16pt;" size="4">WA3DSP</font><font style="font-size:16pt;" size="4"><br></font><font style="font-size:16pt;" size="4">http://www.crompton.com/hamradio</font></b><font style="font-size:16pt;" size="4"><br></font><br><br><div><hr id="stopSpelling">From: joe@ad2dx.us<br>To: arm-allstar@hamvoip.org<br>Date: Sat, 28 Mar 2015 05:07:10 +0000<br>Subject: Re: [arm-allstar] FT-2900R COS Signal<br><br>
<style><!--
.ExternalClass .ecxhmmessage p {
padding:0px;
}
.ExternalClass body.ecxhmmessage {
font-size:12pt;
font-family:Calibri;
}
--></style><style id="ecxowaParaStyle">
</style>
<div style="direction:ltr;font-family:Tahoma;color:#000000;font-size:10pt;">Thanks Doug. I guess I need to understand COS a bit more. It appears that COS is a digital low or high (0V or +5V). I did find AF mute on a 16 pin DIP at pin12, so I guess I need
to probe it with my logic probe while listening to squelch open and closed on a received signal.
<div><br>
</div>
<div>I don't have a scope but I think my logic probe will give me enough info. I wonder if I have to buffer that signal if I try to use it as a COS line for the URI, if the URI loads that signal down too much, or if I can just take the signal right off that
pin. I suspect no buffer would be needed.</div>
<div><br>
</div>
<div>Time to look at the URI schematic too...</div>
<div><br>
</div>
<div>Thanks.<br>
<div><br>
<div style="font-family:Tahoma;font-size:13px;">
<div style="font-family:Tahoma;font-size:13px;">
<div style="font-family:Tahoma;font-size:13px;">Joe Lauricella, AD2DX</div>
<div style="font-family:Tahoma;font-size:13px;">joe at AD2DX dot US</div>
<div style="font-family:Tahoma;font-size:13px;">609-737-7064</div>
</div>
</div>
</div>
<div style="font-family:Times New Roman;color:#000000;font-size:16px;">
<hr tabindex="-1">
<div id="ecxdivRpF824175" style="direction:ltr;"><font color="#000000" size="2" face="Tahoma"><b>From:</b> arm-allstar-bounces@hamvoip.org [arm-allstar-bounces@hamvoip.org] on behalf of Doug Crompton [doug@crompton.com]<br>
<b>Sent:</b> Friday, March 27, 2015 11:20 PM<br>
<b>To:</b> BeagleBone Black ARM Allstar<br>
<b>Subject:</b> Re: [arm-allstar] FT-2900R COS Signal<br>
</font><br>
</div>
<div></div>
<div>
<div dir="ltr"><font style="" color="#000000" face="Tahoma,sans-serif">Joe,<br>
<br>
Check out the service manual - <br>
<br>
<a href="http://elektrotanya.com/yaesu_ft-2900r_sm.pdf/download.html" target="_blank">http://elektrotanya.com/yaesu_ft-2900r_sm.pdf/download.html</a><br>
<br>
main unit schematic. It looks like AF mute is a place to look. You will need to check levels with a signal. It is best to have a low (0 volt) signal on PL receive.<br id="ecxFontBreak">
</font><br>
<br>
<b><font style="font-size:16pt;" size="4">73 Doug</font><font style="font-size:16pt;" size="4"><br>
</font><font style="font-size:16pt;" size="4">WA3DSP</font><font style="font-size:16pt;" size="4"><br>
</font><font style="font-size:16pt;" size="4">http://www.crompton.com/hamradio</font></b><font style="font-size:16pt;" size="4"><br>
</font><br>
<br>
<div>
<hr id="ecxstopSpelling">
From: joe@ad2dx.us<br>
To: arm-allstar@hamvoip.org<br>
Date: Fri, 27 Mar 2015 21:52:25 +0000<br>
Subject: [arm-allstar] FT-2900R COS Signal<br>
<br>
Hi Folks,
<div>Does anyone know where I can find the COS signal inside the Yaesu FT-2900R? I can get TX/RX audio, PTT and ground from the outside of the unit but I poured through the schematics and cannot locate COS.</div>
<div>Thanks in advance.<br>
<div>
<div style="color:rgb(0,0,0);font-family:Helvetica;font-style:normal;font-variant:normal;font-weight:normal;letter-spacing:normal;line-height:normal;orphans:2;text-indent:0px;text-transform:none;white-space:normal;widows:2;word-spacing:0px;word-wrap:break-word;">
<div>73</div>
<div>Joe - AD2DX</div>
<div><br>
</div>
</div>
<br class="ecxApple-interchange-newline">
<br class="ecxApple-interchange-newline">
</div>
<br>
</div>
This email communication and any files transmitted with it may contain confidential and or proprietary information and is provided for the use of the intended recipient only. Any review, retransmission or dissemination of this information by anyone other than
the intended recipient is prohibited. If you receive this email in error, please contact the sender and delete this communication and any copies immediately. Thank you.
<br>
_______________________________________________ arm-allstar mailing list arm-allstar@hamvoip.org http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/</div>
</div>
</div>
</div>
</div>
</div>
This email communication and any files transmitted with it may contain confidential and or proprietary information and is provided for the use of the intended recipient only. Any review, retransmission or dissemination of this information by anyone other than
the intended recipient is prohibited. If you receive this email in error, please contact the sender and delete this communication and any copies immediately. Thank you.
<br>_______________________________________________
arm-allstar mailing list
arm-allstar@hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/</div> </div></body>
</html>