[arm-allstar] Immediate disconnect

Mon Jun 19 11:57:44 EDT 2023

Your main issue is this,

You have node 59251 then 1998 in the same line.  Change 1998 to 59251.

phone-iaxrpt] ;;; Stanza is the context from iax.conf
exten => 59251,1,Answer
exten => 59251,n,Playback,rpt/node
exten => 59251,n,Playback,digits/1
exten => 59251,n,Playback,digits/9
exten => 59251,n,Playback,digits/9
exten => 59251,n,Playback,digits/9
exten => 59251,n,Set(CALLERID(num)=0)
exten => 59251,n,Rpt,1998|P|${CALLERID(name)} ;;; The "CallerID"
from IAXRpt

See ^^^

Change that, save, and reboot.

Mike

On Mon, Jun 19, 2023, 7:49 AM Ian via ARM-allstar <arm-allstar at hamvoip.org>
wrote:

>
> Hi Michael,
>
> Thanks for offering to take a look at the conf file for me. I now suspect
> the problem is actually
> that I haven't set up DVSwitch properly, I'll have to spend some time and
> effort attempting to
> understanding the whole ecosystem a little better.
>
> All the conf files were configured automatically with the initial setup
> script, all I have changed
> in the extensions.conf file is the last playback number in the
> [phone-iaxrpt] stanza from
> 8 to 9 which I imagine is inconsequential. I'd be curious to know if you
> can connect to my
> node, if you can then this might isolate the problem to my DVS mobile
> setup.
>
> Also just noticed that perhaps I should have commented out all references
> to 1999?
>
> Thanks for your help, regards,
>
> Ian
>
>
> ; WARNING - THIS FILE WAS AUTOMATICALLY CONFIGURED FROM A
> ; TEMPLATE FILE IN   /usr/local/etc/asterisk_tpl   BY THE
> ; NODE-CONFIG.SH SCRIPT.
> ;
> ; EACH TIME THIS SCRIPT IS RUN, THIS FILE WILL BE OVERWRITTEN.
> ; IF YOU CHANGE ANYTHING IN THIS FILE AND RUN THE NODE-CONFIG.SH
> ; SCRIPT, IT WILL BE LOST.
> ;
> ; IF YOU INTEND TO USE THE NODE-CONFIG.SH SCRIPT,  THEN YOU SHOULD
> ; MAKE MODIFICATIONS TO THE ACTUAL TEMPLATE FILES LOCATED IN
> ; /usr/local/etc/asterisk_tpl directory.
> ;
> ; Shown for two nodes, second node commented out.
> ; change ALL 59251 and 1999 (if second node used) to
> ; your local node numbers
>
> ; Updated 1/2019 to include additional features
> ; Before attempting to add features ensure they
> ; are not already installed
>
> [general]
>
> static=yes       ; These two lines prevent the command-line
> interface
> writeprotect=yes ; from overwriting the config file. Leave them
> here.
>
> [globals]
> HOMENPA=215
>
> [default]
> exten => i,1,Hangup
>
> [radio-secure]
> exten => 59251,1,rpt,59251
> exten => 1999,1,rpt,1999
>
> [radio-secure-proxy]
> exten => 59251,1,rpt,59251|X
> exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1)
>
> ; IAXRPT Windows
>
> [radio-iaxrpt]
> exten=59251,1,Rpt,59251|X
> exten=1999,1,Rpt,1999|X
>
> ; The following stanza is to be used for Android/Iphone
> ; connections. Please configure the node number for the
> ; node on this server you want to connect to.
> ; The callerID name is configured and returned from
> ; your phone. It is typically your call.
>
> [phone-iaxrpt]    ;;; Stanza is the context from iax.conf
> exten => 59251,1,Answer
> exten => 59251,n,Playback,rpt/node
> exten => 59251,n,Playback,digits/1
> exten => 59251,n,Playback,digits/9
> exten => 59251,n,Playback,digits/9
> exten => 59251,n,Playback,digits/9
> exten => 59251,n,Set(CALLERID(num)=0)
> exten => 59251,n,Rpt,1998|P|${CALLERID(name)} ;;; The "CallerID"
> from IAXRpt
>
> ; To make this have a static callerID name if your phone
> ; app does not support callerID change the last line to this
> ; and specify the name (usually CALL) in place of static-name.
>
> ;exten => 59251,n,Rpt,1998|P|"static-name"
>
> ; Autopatch example lines. Must be configured and
> ; SIP or IAX phone connections configured to work.
>
> [pstn-out]
> exten=_NXXNXXXXXX,1,playback(ss-noservice)
> exten=_NXXNXXXXXX,2,Congestion
>
> [invalidnum]
> exten=s,1,Wait,3
> exten=s,n,Playback,ss-noservice
> exten=s,n,Wait,1
> exten=s,n,Hangup
>
> [radio]
> exten=_X11,1,Goto(check_route|${EXTEN}|1);
> exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1)
> exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1)
>
> [check_route]
> ; no 800
> exten=_1800NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1888NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1877NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1866NXXXXXX,2,Goto(invalidnum|s|1)
> exten=_1855NXXXXXX,2,Goto(invalidnum|s|1)
> ; no X00 NPA
> exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1)
> ; no X11 NPA
> exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1)
> ; no X11
> exten=_X11,2,Goto(invalidnum|s|1)
> ; no 555 Prefix in any NPA
> exten=_1NXX555XXXX,2,Goto(invalidnum|s|1)
> ; no 976 Prefix in any NPA
> exten=_1NXX976XXXX,2,Goto(invalidnum|s|1)
> ; no NPA=809
> exten=_1809XXXXXXX,2,Goto(invalidnum|s|1)
> ; no NPA=900
> exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)
>
> ; okay, route it
> exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1)
> exten=_X.,2,Goto(invalidnum|s|1)
>
> ; End autopatch example
>
> ; Following stanza required for web transceiver access
>
> [allstar-public]
>
> exten => s,1,Ringing
> exten =>
> s,n,Set(RESP=${CURL(https://register.allstarlink.org/cgi-bin/authwe
> bphone.pl?${CALLERID(name)})
> <https://register.allstarlink.org/cgi-bin/authwebphone.pl?$%7BCALLERID(name)%7D)>
> })
> exten => s,n,Set(NODENUM=${CALLERID(number)})
> exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit)
> exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit)
> exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit)
> exten => s,n,Set(CALLSIGN=${RESP:5})
> exten => s,n,Wait(3)
> exten => s,n,Playback(rpt/node|noanswer)
> exten => s,n,Saydigits(${NODENUM})
> exten => s,n,Set(CALLERID(num)=0)
> exten => s,n,Set(CALLERID(name)=${CALLSIGN})
> exten => s,n,Rpt(${NODENUM}|X)
> exten => s,n,Hangup
> exten => s,n(hangit),Answer
> exten => s,n(hangit),Wait(1)
> exten => s,n(hangit),Hangup
>
> exten => 9999,1,Goto(allstar-public|s|1)
>
> ; end web transceiver stanza
>
> ; Following stanza required for phone access
>
> [allstar-sys]
>
> exten => _x.,1,Ringing
> exten => _x.,n,Wait(3)
> exten => _x.,n,Answer
> exten => _x.,n,Playback(rpt/node)
> exten => _x.,n,Saydigits(${EXTEN:1})
> exten => _x.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P)
> exten => _x.,n,Hangup
>
> ; end phone access stanza
>
> ; The blacklist and whitelist stanzas below are used to allow or
> ban nodes
> ; from connecting. Only one can be selected at a time as defined in
> the
> ; [radio] stanza of iax.conf
> ;
> ; The best way to allow or ban nodes from the database is to
> ; use the Supermon application or the node-ban-allow.sh script.
> ;
> ; No changes need to be made to these stanzas. See comments in
> iax.conf.
>
> [blacklist]
> exten => _XXXX!,1,NoOp(${CALLERID(num)})
> exten =>
> _XXXX!,n,GotoIf($[${DB_EXISTS(blacklist/${CALLERID(num)})}]?blocked
> )
> exten => _XXXX!,n,Goto(radio-secure,${EXTEN},1)
> exten => _XXXX!,n(blocked),Hangup
>
> [whitelist]
> exten => _XXXX!,1,NoOp(${CALLERID(num)})
> exten => _XXXX!,n,NoOp(${IAXPEER(CURRENTCHANNEL)})
> exten => _XXXX!,n,GotoIf($["${IAXPEER(CURRENTCHANNEL)}" =
> "127.0.0.1"]?radio-secure,${EXTEN},1)  ;permit local IPs
> exten =>
> _XXXX!,n,GotoIf($[${DB_EXISTS(whitelist/${CALLERID(num)})}]?radio-s
> ecure,${EXTEN},1)
> exten => _XXXX!,n,Hangup
>
> ; Stanza to get node number and pass to saydns.sh script in
> rpt.conf
> [saydns]
> exten => _xxx.,1,System(/usr/local/sbin/saydns.sh ${EXTEN})
> exten => _xxx.,n,Hangup()
>
> ; Example connection to another Asterisk server
> ; and passing an extension
>
> ; [pbx_server]
> ;exten => _1NXXNXXXXXX,1,Dial(IAX2/pbx/${EXTEN})
> ;exten => _NXXNXXXXXX,1,Dial(IAX2/pbx/${EXTEN})
> ;exten => _NXX,1,Dial(IAX2/pbx/${EXTEN})
> ;exten => _NX,1,Dial(IAX2/pbx/${EXTEN})
>
> #includeifexists custom/extensions.conf
>
>
>
> On 17 Jun 2023 at 19:45, Michael Webb via ARM-allstar wrote:
>
> > You can post your extensiona.conf file here and I can take a look at
> > it.
> >
> > On Sat, Jun 17, 2023, 7:44 PM Ian via ARM-allstar
> > <arm-allstar at hamvoip.org> wrote:
> >
> > >
> > > Hi Michael,
> > >
> > > Thanks for replying. You're right, the audio is coming from the
> > > [phone-iaxrpt] stanza, it plays 1998 (now fixed) while everything
> > > else is 1999, although I can't figure out why it disconnects. There
> > > is obviously something fundamentally wrong with my configuration.
> > >
> > > I think I'll take a break and restart from scratch some time later
> > > after doing a bit more research. It's much more complex than I
> > > expected.
> > >
> > > Regards,
> > >
> > > Ian
> > >
> > >
> > > On 17 Jun 2023 at 7:23, Michael Webb via ARM-allstar wrote:
> > >
> > > > Check extensions.conf and make sure all the node numbers are
> > > > correct throughout each line.  I've seen some start off as one
> > > > number and then throw a different digit in there.  Such as 1998
> > > > then 1999 or the other way around.
> > > >
> > > > On Sat, Jun 17, 2023, 7:04 AM Ian via ARM-allstar
> > > > <arm-allstar at hamvoip.org> wrote:
> > > >
> > > > > I've just set up hamvoip on a RPi 3B, but have yet to connect it
> > > > > to a radio.
> > > > >
> > > > > When trying to connect to my (external) node using DVSwitch
> > > > > mobile, it announces an internal node (1998) then immediately
> > > > > disconnects. Any ideas?
> > > > >
> > > > > I have to admit I'm not a linux guy, and it's taken me a day of
> > > > > hair pulling frustration to get this far, so be gentle. Thanks!
> > > > > _______________________________________________
> > > > >
> > > > > ARM-allstar mailing list
> > > > > ARM-allstar at hamvoip.org
> > > > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > > > >
> > > > > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> > > > >
> > > > _______________________________________________
> > > >
> > > > ARM-allstar mailing list
> > > > ARM-allstar at hamvoip.org
> > > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > > >
> > > > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> > >
> > >
> > > _______________________________________________
> > >
> > > ARM-allstar mailing list
> > > ARM-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> > >
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>
>
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Screenshot_20230619-105412.png
Type: image/png
Size: 192779 bytes
Desc: not available
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20230619/238f9f5c/attachment.png>