[arm-allstar] Connect and Disconnect - Tones only without voice announcement

[Dave Petrie]

Hi Travis, I think I got it, just to be sure, there is already a way to
have a tone or cw when no other node or connection  is connected to your
node, and a different tone or cw character when another node is connected,
that node can be distant or on the same raspberry, it's a node connected.
So that's the first two choices or I should say
status. Then there is the courtesy tone that is sent when a local connect
to the node unkeys, normally the repeater receiver or remote or link radio
stops receiving signal, that's a tone or cw and then there is a tone or cw
for when the connected node unkeys. So you know when at least one other
node is connected or no one is connected and you know who just unkeyed,
local access or remote linked access.
I have the "do da loop" melody or tone as you might call it when no other
nodes are connected, I have three nodes, Allstar 40039, my repeater 5086,
my remote base 5000.
I have the rpt.conf set for 5086 to connect to 40039 on boot up. So when i
unkey with my HT i get a cw k and when someone from the allstar linking via
40039 or echolink which is also on 40039 node, unkey's I hear a cw L.
I think you would like to have in addition to what I just described,
another tone or cw when additional nodes connect and disconnect. If the
distant node connects in Monitor mode to your node you won't get any
indication by sound, but if you are watching your supermon screen you will
see the connect and disconnect. You mentioned email alerts, which is
something I haven't tried yet.
Did I get it right so far? Or would you like the lines in rpt.conf to make
the changes I just described.
Dave

On Wed, Oct 27, 2021 at 7:54 AM Travis French <tfrench at pcb.com> wrote:

> Good Morning Dave,
>
> I was thinking of that as well to just disable telemetry on the fly but
> was really hoping for something more permanent and streamlined.
>
> I was envisioning the following:
>
> Any Connect = a very specific high tone or sequence or maybe a morse code
> "C"
> Any Disconnect = a very specific low tone or sequence or maybe a morse
> code "D"
>
> I was thinking one of these options were already built in.
>
> The other idea I had, as I do something like this on one of my other
> nodes, was to turn telemetry off, intercept the connect and disconnect
> logging scripts, and insert a command before logging to make the
> appropriate tone announcement. This specific script sends an email so it
> has nothing to do with telemetry. I am just wondering if turning off
> telemetry would block this announcement. I think this way could be doable
> and would need to be validated but didn't want to go that route if there
> was a more simple option.
>
> Still playing.
>
> Thank you in advance,
>
> Travis - K2PCB
>
>
>
>
> -----Original Message-----
> From: ARM-allstar <arm-allstar-bounces at hamvoip.org> On Behalf Of "Dave
> Petrie via ARM-allstar"
> Sent: Tuesday, October 26, 2021 9:47 PM
> To: ARM Allstar <arm-allstar at hamvoip.org>
> Cc: Dave Petrie <wa2kjc at gmail.com>
> Subject: Re: [arm-allstar] Connect and Disconnect - Tones only without
> voice announcement
>
>
>
> External Email Notice: This email originated from outside the PCB /
> Temposonics organization.
>
>
>
>
> Hi Travis, I am not sure what you mean by tones, courteous unkey tones ? I
> use cw k when someone on my node unkeys and cw L when someone on a
> connected link unkeys. I use dtmf to turn telemetry on and off. During nets
> that I listen to the telemetry gets in the way.
> in /etc/asterisk  rpt.conf  i assigned 984 and 986 to cop commands, but
> you can use whatever is available to you.
>
> [functions<your node>]
>
> 984=cop,33 ;telemetry enable ;turn on voice announcements
> 986=cop,34;telemetry disable ;tunr off voice announcements
>
> So I send *984 to turn on voice and *986 to turn it off.
>
> Hope that helps.
> Dave
>
> On Tue, Oct 26, 2021 at 7:10 PM "Travis French via ARM-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > Good Morning,
> >
> > I am sure I am staring right at it but for the life of me, I am not
> > finding the option to reduce the connect and disconnect announcements
> > to tones only. I believe I have seen this before but can't seem to
> > remember where this option resides. I would prefer not to disable
> > external telemetry all together let alone reduce it to 1 minute. I am
> > just looking to drop the voice portion of the connect and disconnect
> > messages and only hear the tones.
> >
> > This is an option, correct?
> >
> > Thank you in advance,
> >
> > Travis - K2PCB
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> >
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>
>