[arm-allstar] Adding Second Node to Server

[Doug Crompton]

Kevin,

  Following the procedure on those pages is what associates them. Once they
are set you need to mark where they are plugged in and make sure you don't
physically swap things.

*73 Doug, WA3DSP*
*http://wa3dsp.org <http://wa3dsp.org>*

On Mon, Apr 20, 2020 at 12:36 PM "Kevin Davis via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> I thought I had following the directions to a tea, but I'll give it another
> shot.
>
> For my understanding, how does Asterisk know which physical USB port is
> associated with which simpleusb stanza?
>
> On Mon, Apr 20, 2020 at 9:29 AM "Doug Crompton via ARM-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > Kevin,
> >
> >  You need to add the second FOB as per the instructions on pages 10-12 at
> > the end of the setup docs. There is a specific order. If it is not
> > associating make sure you have TWO active stanzas in simpleusb.conf
> > defined. Whatever they are called, lets say [USB1] and [USB2] or they
> could
> > be called the node numbers for distinction, you must also have a
> > corresponding rxchannel=SimpleUSB/usb1 in the first node stanza and
> > rxchannel=SimpleUSB/usb2  in the second node stanza in rpt.conf. The
> names
> > must match, so if you did use node numbers say [56001] in simpleusb then
> it
> > would be  rxchannel=SimpleUSB/56001  in rpt.conf.
> >
> > *73 Doug, WA3DSP*
> > *http://wa3dsp.org <http://wa3dsp.org>*
> >
> >
> > On Mon, Apr 20, 2020 at 11:10 AM "Kevin Davis via ARM-allstar" <
> > arm-allstar at hamvoip.org> wrote:
> >
> > > Over the weekend, I tried to add a second node to my server and
> couldn't
> > > seem to get all my dots connected.
> > >
> > > The server currently has one radio-less node and I was attempting to
> add
> > an
> > > Alinco Dr-135 as my second node.
> > >
> > > I was going off pages 10-12 of this document.
> > > https://www.hamvoip.org/config-setup.pdf
> > >
> > > The document doesn't go into specifics re: the extensions.conf or
> > iax.conf
> > > changes, but I think I did those correctly.
> > >
> > > My problem seems to be that once I plug the new FOB in, it's not
> getting
> > > associated with the usb2 stanza in simpleusb correctly.  What is going
> on
> > > behinds the scenes when I restart Asterisk after plugging in the new
> FOB
> > > that ties it to the correct simpleusb stanza?
> > >
> > > Thanks for any pointers!
> > >
> > > -Kevin (KE7K)
> > > _______________________________________________
> > >
> > > ARM-allstar mailing list
> > > ARM-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> > >
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
> >
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3/4 web page - http://hamvoip.org
>