[arm-allstar] 3G Dongle with Hamvoip on PI

[Doug Crompton]

It sounds like maybe there should be a howto on this and from your
description I guess one could be created. The problem I see is the
complexity of it over just using a hotspot. The advantage would be more
self contained and once it was setup it should just work anywhere you have
cell service with that provider. But as was pointed out the carriers are
constantly changing things and at least the hotspot method to a phone or
external device should always be there.


*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*

On Fri, Jul 19, 2019 at 12:55 PM "Lawrence Roney via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> Hi Rachid,
>
> If I understand correctly, you want to use a cellular dongle (USB modem)
> that plugs into the Pi, vs. an external cellular/Wi-Fi hotspot.  I've had
> good success with a Huawei E397u-53 dongle for this purpose.  It is
> self-contained, powered directly from the Pi, and does not require the use
> of Wi-Fi from a separate hotspot device.
>
> In the USA, I have it activated on a T-Mobile LTE, unlimited $10 per month
> plan (2GB high speed, then rate limited, but the limited speed is more than
> adequate for Allstar VoIP traffic)
>
> To set it up:
> You need to install the USB Modeswitch utility to force the dongle into
> modem mode.  They usually start out in CD ROM emulation mode to load their
> Windows drivers, etc.   This is done with:  pacman -S usb_modeswitch
>
> Then, install a PPP stack on the Pi with:  pacman -S ppp   (this may
> already be included in the recent HamVoIP distribution)
>
> You will need to create an /etc/chatscripts/carrier_name configuration
> file  (where "carrier_name" is the name of your cell provider, ex. Verizon,
> T-Mobile etc.)  This file sends the connection setup, "AT" commands to the
> modem's dialer and looks for the expected responses.  This file also
> contains the carrier specific access point name (APN) information that
> tells the modem what to "dial" to join the carrier's mobile data network.
> For example, my T-Mobile chatscript file has the line:  OK
> AT+CGDCONT=1,"IP","fast.t-mobile.com"   YOU WILL NEED TO RESEARCH YOUR
> CARRIER'S SPECIFIC APN AND THE ZTE MODEM COMMANDS
>
> You will need to create an /etc/ppp/peers/carrier_name file.  This file
> contains the configuration settings for the PPP session.
>
> Archlinux will create a new ppp0 interface for the modem.  (Note: Make
> sure the eth0 interface is set to DHCP and is unplugged, otherwise the
> default route will not change to ppp0)
>
> To connect, at the Linux prompt start the PPP session by typing: pon
> carrier_name   (where "carrier_name" is the filename of the chatscript and
> peers files created in the previous steps)
>
> To disconnect, at the Linix prompt, type: poff
>
> On my Pi, I added automatic startup configurations in /etc/rc.local and
> on-demand DTMF macro sequences in /etc/asterisk/rpt.conf  to bring up/down
> the PPP connection.
>
> Hope this helps to get you started.  Email me directly if you would like
> specific notes and chatscript file examples for how I setup the Huawei
> E397u-53 (available on Amazon) for use on the US T-Mobile LTE network.
>
> 73,
> Lawrence - N6YFN
>
>
>
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>