[arm-allstar] Cross Band Repeater with DMK URI Possible?

[Doug Crompton]

Kyle,

 I highly recommend the TechnoByGeorge.com  ARN-1.  It works very well and
is easy to use.


*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*

On Fri, Jul 12, 2019 at 9:04 PM "Kyle Krieg via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> Yep, will do David and Doug.  Thanks for the info.  I kinda figured there
> was a way, but didn't think about linking both private nodes together
> internally and using 2 FOB's.  I'll try that later this week.
>
> Is there a list of FOB's that specially work with AllStar?  I know FOB's
> from Master Communications work, as I just discovered them in Dayton this
> year.  I'm sure there more?  Looking for more than just a sound card.
>
> Kyle
>
>
> On Fri, Jul 12, 2019 at 6:56 PM "Doug Crompton via ARM-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > Also keep in mind there is nothing special about the DMK URI.  Any
> > compatible sound FOB will work here.
> >
> >
> > *73 Doug*
> >
> > *WA3DSP*
> >
> > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> >
> > On Fri, Jul 12, 2019 at 5:02 PM "David McGough via ARM-allstar" <
> > arm-allstar at hamvoip.org> wrote:
> >
> > >
> > >
> > > Sure, that'll work fine, but, it'll require 2 URI's. Setup each node
> as a
> > > simplex node (duplex=1) and then link both nodes together.
> > >
> > > Obviously watch out for TX duty cycle on either radio.
> > >
> > > 73, David KB4FXC
> > >
> > >
> > >
> > > On Fri, 12 Jul 2019, "Kyle Krieg via ARM-allstar" wrote:
> > >
> > > > Our club and area hams provide bike event support in September for a
> > > > 150mile, 2 day 1500 bike fundraiser.
> > > >
> > > > One of the longer routes on Sunday requires us to use 2m to a
> centrally
> > > > located school for the SAG vans and rest stops and then a 70cm yagi
> > link
> > > > back to net control at the area college so we don't step on any of
> the
> > > > remaining 2m simplex frequencies.
> > > >
> > > > I have a couple of old ICOM radios with external pin outs here I can
> > > throw
> > > > together.
> > > >
> > > > Would AllStar have the capability with full duplex mode to configure
> it
> > > for
> > > > a full cross band repeater with a 2m and 70cm radio?  In/out 70cm and
> > > > in/out 2m?
> > > >
> > > > Running HamVoIP into a Pi.
> > > >
> > > > Kyle
> > > > AA0Z
> > > > _______________________________________________
> > > >
> > > > ARM-allstar mailing list
> > > > ARM-allstar at hamvoip.org
> > > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > > >
> > > > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > > >
> > >
> > > _______________________________________________
> > >
> > > ARM-allstar mailing list
> > > ARM-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > >
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>