[arm-allstar] Using a FT-2500M as a simplex node radio

[David Travis]

I have used the ft-2500m in this configuration just be aware that even with PL tone is being used it will still see a carrier without pl tone and activate just be aware


Sent from Windows Mail

From: Doug Crompton via ARM-allstar<mailto:arm-allstar at hamvoip.org>
Sent: ‎Tuesday‎, ‎April‎ ‎9‎, ‎2019 ‎10‎:‎27‎ ‎AM
To: ARM Allstar<mailto:arm-allstar at hamvoip.org>
Cc: Doug Crompton<mailto:wa3dsp at gmail.com>

Russ,

I believe the mic is an RJ-45 so you could cut an old Ethernet patch cord
and then wire the correct connections to a FOB. Yes, George has a couple of
new FOB's available that work well at a very reasonable price. Contact him
at Techno.bygeorge at gmail.com. I am not where I can send you a copy of the
manual at the moment but it would be an easy wiring job.

Doug

On Tue, Apr 9, 2019 at 11:07 AM "Russell Thomas via ARM-allstar" <
arm-allstar at hamvoip.org> wrote:

> did i hear George might have a new FOB coming out?
>
>
>
> On Sat, Apr 6, 2019 at 6:37 PM "Doug Crompton via ARM-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
> > Russ,
> >
> >  Refer to the manual page 44, 45  -
> >
> > This isn't the best manual download. If you don't have a manual you can
> use
> > this link or find a better one -
> >
> > http://www.iw2nmx.it/Yaesu/FT-2500M/FT-2500M%20Instruction%20Manual.pdf
> >
> > There apparently is an internal jumper to give COS on pin 1 of the mic
> > jack. Doing that you would have everything you need on the mic jack
> > including RX audio.
> >
> >
> > *73 Doug*
> >
> > *WA3DSP*
> >
> > *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
> >
> >
> >
> > On Sat, Apr 6, 2019 at 7:29 PM "Russell Thomas via ARM-allstar" <
> > arm-allstar at hamvoip.org> wrote:
> >
> > > I have a Yaesu FT-2500M sitting around not doing nothing. I also have a
> > 2 m
> > > all directional antenna about 45 ft in the air.
> > > I was thinking about putting both to good use again in the form of an
> > > All-Star simplex node.
> > > The manual shows the pins for the microphone and in the past I have
> > built a
> > > tnc for APRS for it.
> > > What would it take to interface this radio to a PI with the Ham VOIP
> > image?
> > >
> > > 73,
> > > Russell Thomas, KV4S
> > > DMR TG: 240218 | YSF: US KV4S | D-STAR: XRF334R
> > > Allstar: 47923 | IRLP: 4535 | EchoLink: KV4S-L
> > > Web: http://KV4S.com
> > > _______________________________________________
> > >
> > > ARM-allstar mailing list
> > > ARM-allstar at hamvoip.org
> > > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> > >
> > > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> > >
> > _______________________________________________
> >
> > ARM-allstar mailing list
> > ARM-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2/3 web page - http://hamvoip.org
> >
> _______________________________________________
>
> ARM-allstar mailing list
> ARM-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>
_______________________________________________

ARM-allstar mailing list
ARM-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2/3 web page - http://hamvoip.org