[arm-allstar] Node keeps rekeying up

Wed Jul 25 11:28:06 EST 2018

Doug,

Copy all and fully understand.  All my repeaters transmit PL that 
follows the input.  Courtesy tones, announcements, idle ID's, etc are 
not transmitted with tone.

With regard to the node, are you saying there is no means to control IP 
encode via HamVoIP?  To me, it would be very desirable to have the 
capability to set PL encode to follow the node input, thereby 
eliminating node IDs on the repeater system.

The main reason I set PL to follow the input is to eliminate CTs and IDs 
from my Echolink node, but a side benefit of this method is that users 
can set their radio to decode my tone and never have to listen to the 
extraneous stuff.  If my node is always going to encode PL when it 
transmits, then they are always going to hear the node IDs.  Personally, 
I'd rather not have the node IDs go out over the system, especially when 
it's linked to our wide-area intertie.

If controlling PL isn't an option via AVI at this time, perhaps it can 
be added in a future revision.  In the meantime, I can probably control 
encode directly from the COS line.

Just my 2-cents worth.

73,

Mike
WM4B

On Wed, Jul 25, 2018 at 11:51 AM, "Doug Crompton via arm-allstar" wrote:

> Connecting a simplex node to a repeater requires some planning and 
> always
> the permission of the repeater owner. I will call this the "poor mans" 
> way
> to get Allstar on the repeater. The best way is having Internet at the
> repeater and interfacing Allstar there either using Allstar as the 
> repeater
> controller or bringing it in on a port of an existing controller.
>
> In the event this is not possible there are things you can do to make 
> it
> work reasonably well. I personally have a repeater that does not have
> access to the Internet and I use a remote simplex node to provide full 
> time
> Allstar on that repeater. The key is to have the repeater PL follow 
> the
> input to the repeater not the output. Then your remote simplex node 
> sees
> keyups like they were coming directly from the input station to the
> repeater and not the repeater itself thus eliminating the repeater 
> tail and
> ID from being transmitted out over Allstar. This would require a 
> change at
> the repeater. The downside is that the repeater users would not hear 
> the
> repeater tail or ID either if they were using tone squelch. You could 
> add a
> second PL so that one followed the repeater input and one followed the
> repeater output so both repeater users and Allstar would be happy BUT 
> if
> this is a full time Allstar connection there would be no reason to do 
> that.
> The remote simplex node stays in duplex=1 with no other changes. Its
> courtesy tone becomes the repeater courtesy tone and tail that the 
> users
> would hear. When the repeater unkeys it would either not have a PL or 
> have
> a PL that the remote simplex Allstar node would not respond to thus no
> keyup loop.
>
> When doing this you can set the repeater to have a short CW ID and let 
> the
> remote simplex node do a normal ID. Repeater users would just have to 
> get
> use to hearing it and observe the rules of Allstar - no quick keyups. 
> The
> key here is not being upset that Allstar is being added to the 
> repeater and
> accepting some changes. Many of the repeaters we have are not being 
> used or
> utilized beyond a few keyups a day. Adding Allstar could be a big 
> benefit
> but requires some education and understanding that things will change 
> a bit.
>
>
> *73 Doug*
>
> *WA3DSP*
>
> *http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*
>
> On Wed, Jul 25, 2018 at 6:50 AM, "Mike Besemer - WM4B via arm-allstar" 
> <
> arm-allstar at hamvoip.org> wrote:
>
>> Doug,
>>
>> I'm interested in hearing the fix for this, as it exactly describes 
>> the
>> situation with the node I'm building.
>>
>> The repeater it will be connected to is mine.  It does not transmit 
>> CTCSS
>> on IDs or announcements, so that will prevent half of the ping-pong 
>> cycle.
>> Is there a way to have the node transmit IDs without CTCSS?
>>
>> Mike
>> WM4B
>>
>>
>> On Wed, Jul 25, 2018 at 12:31 AM, "Doug Crompton via arm-allstar" 
>> wrote:
>>
>> John,
>>>
>>>  You cannot connect a simplex node to a repeater without some 
>>> adjustments.
>>> The problem is your node has a courtesy tone which keys up on RF 
>>> after the
>>> repeater drops. The repeater hears this and again keys up and a loop
>>> forms.
>>> To eliminate this you need to set  nounkeyct=1  in rpt.conf  - the 
>>> default
>>> is =0 or perform the tone. You could also set duplex=0 instead but 
>>> that
>>> eliminates many other telemetry things you may want to maintain. 
>>> When you
>>> make changes to the config files you must restart asterisk or reboot 
>>> the
>>> system for them to take effect.
>>>
>>> Connecting a simplex node to a repeater is not a good idea unless 
>>> you
>>> either own the repeater or have permission to do so. You ID's will 
>>> show up
>>> on the repeater and the repeater ID's will go out over the nde and 
>>> to
>>> wherever it is connected. There are ways around this if you have 
>>> control
>>> over the repeater. If that is the case and you want more info let me 
>>> know.
>>>
>>>
>>> *73 Doug*
>>>
>>> *WA3DSP*
>>>
>>> *http://www.crompton.com/hamradio 
>>> <http://www.crompton.com/hamradio>*
>>>
>>>
>>> On Wed, Jul 25, 2018 at 12:08 AM, "w7jca via arm-allstar" <
>>> arm-allstar at hamvoip.org> wrote:
>>>
>>> Good evening,
>>>>
>>>>
>>>>
>>>> I have a RP3 and DMK URI hooked up to a Motorola CDM 1550. It is 
>>>> set to
>>>> duplex=1 and is a RF node to a repeater. Everything is working fine
>>>> except
>>>> when someone unkeys the node keys up for a second. It continues to 
>>>> do
>>>> this
>>>> each time someone unkeys. I have courtesy tones turned off and 
>>>> still no
>>>> change. It does this on Allstar as well as echolink.
>>>>
>>>> Any help would be appreciated.
>>>>
>>>>
>>>>
>>>> Thanks
>>>>
>>>>
>>>>
>>>> John W7 JCA
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>>
>>>> arm-allstar mailing list
>>>> arm-allstar at hamvoip.org
>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>
>>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>>>
>>>> _______________________________________________
>>>
>>> arm-allstar mailing list
>>> arm-allstar at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>
>>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>>
>> _______________________________________________
>>
>> arm-allstar mailing list
>> arm-allstar at hamvoip.org
>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>
>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org