[arm-allstar] Problems after system update

[Doug Crompton]

Jim,

 If you are not running the beta DNS just do an update as from what you
said in your original message there appears to be a problem in the
rc.allstar file not executing the IP address at boot. See if an update
fixes it. Reboot after the update.

If it is still not saying IP at boot then run this line at the Linux prompt
-

/usr/local/sbin/sayip.sh $NODE1

and see if that say the IP.

Let me know your results.


*73 Doug*

*WA3DSP*

*http://www.crompton.com/hamradio <http://www.crompton.com/hamradio>*




On Sat, Feb 10, 2018 at 2:33 AM, "James R. Pilgram via arm-allstar" <
arm-allstar at hamvoip.org> wrote:

> Thanks Doug,
> So do I just need to run the update? I was a little unclear as the bulk of
> your reply addresses beta dns version. To be perfectly honest I don't know
> what that means.
>
> This node is on a Verizon Mifi and I have installed another raspberry pi 3
> with raspian Jesse and teamviewer so I can get into it remotely.
>
> Jim NH6HI
>
> *From:* arm-allstar at hamvoip.org
> *Sent:* February 9, 2018 21:20
> *To:* arm-allstar at hamvoip.org
> *Reply-to:* arm-allstar at hamvoip.org
> *Cc:* wa3dsp at gmail.com
> *Subject:* Re: [arm-allstar] Problems after system update
>
> Jim,
>
>  I just sent out a fix on this to arm-allstar.  The problem was that early
> DNS instructions conflicted with a change we made in a file. Follow the
> instruction in the email and you should be good.
>
> Doug
>
> On Thu, Feb 8, 2018 at 12:56 AM, "James R. Pilgram via arm-allstar" <
> arm-allstar at hamvoip.org> wrote:
>
>> I experienced the same issue with the IP announcement not working as you
>> did. This was a new install.  On first boot it announced my IP address but
>> after the update and reboot it no longer announced the IP address.  I had
>> to enable that *A1 functions to get the IP address. Never put the 2
>> together till you pointed it out.
>>
>> Jim NH6HI
>>
>> *From:* arm-allstar at hamvoip.org
>> *Sent:* February 7, 2018 19:14
>> *To:* arm-allstar at hamvoip.org
>> *Reply-to:* arm-allstar at hamvoip.org
>> *Cc:* csouleles at prodigy.net
>> *Subject:* [arm-allstar] Problems after system update
>>
>> I just did a system update today (2/7/2018) using PUTTY selecting item 1
>> on the Admin menu.  Right after the update a couple things happened that I
>> can't figure out.
>>
>> 1. My node no longer announces the IP address on start up.  If I do *A1
>> it will announce the IP address, but before the update it would
>> automatically announce it at start up.  It no longer does that.
>>
>> 2.  My halt button on the Raspberry PI3 no longer functions.  Before the
>> update it would halt the RPI3 if I held the button in for six seconds or
>> so. It would announce goodbye system powering down.   Now the button does
>> not halt the processor.  If I do system power down (item 16 on the Admin
>> menu) the processor will halt and then I power it off.  I checked
>> /usr/local/etc/allstar.env and SHUTDOWN_MONITOR is enabled.
>>
>> My node is RPI3, DMK URi, Baofeng UV-82.
>>
>> Any ideas on what I should check?  Thanks,  Chris, W6CS - 73.
>>
>> _______________________________________________
>>
>> arm-allstar mailing list
>> arm-allstar at hamvoip.org
>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>
>> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>>
>
>
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2/3 web page - http://hamvoip.org
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20180210/9ac76a23/attachment-0001.html>