[arm-allstar] DTMF problem

[wade]

Everything but the letter "D" shows up. I had him run the susb tune and 
found the levels were way hot. So after some adjustment we got the RF 
DTMF to work.

Now that brought up another issue both of us have. When running the 
node(s) in simplex we have no reply to functions like *73, *81, *82, but 
we have over the air replies to *70. This is probably just something we 
don't have set correctly but I have not been able to find it since June 
and now that he has this issue I think we should try to resolve it.

These functions did operate correctly when my node was in duplex.

Wade
KC0MLT

On 08/20/2016 05:46 PM, Doug Crompton via arm-allstar wrote:
> Wade,
>
>  It is very unusual for DTMF to not show something in the client even 
> if it is wrong.
>
> asterisk -rvvv
>
> This is what you should see as you hit each tone -
>
> 41139-Mobile*CLI>
> [Aug 20 18:31:24] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 1
> [Aug 20 18:31:25] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 2
> [Aug 20 18:31:26] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 3
> [Aug 20 18:31:26] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 4
> [Aug 20 18:31:27] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 5
> [Aug 20 18:31:28] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 6
> [Aug 20 18:31:28] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 7
> [Aug 20 18:31:29] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 8
> [Aug 20 18:31:31] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 9
> [Aug 20 18:31:32] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char 0
> [Aug 20 18:31:35] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char *
> [Aug 20 18:31:36] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char #
> [Aug 20 18:31:38] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char A
> [Aug 20 18:31:39] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char B
> [Aug 20 18:31:40] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char C
> [Aug 20 18:31:42] NOTICE[334]: chan_simpleusb.c:3042 simpleusb_read: 
> Got DTMF char D
>     -- Hungup 'DAHDI/pseudo-1082656715'
>
> This was done with a Baofeng UV5R with feedback turned off and it has 
> always worked perfectly. See below.
>
> I find it very strange you are seeing nothing. Have you tried other 
> radios? Levels and pre/deemphasis are prime problems. Levels should 
> not be that critical in most cases though.
>
> Are you sure you have node radio RX audio to Allstar? You are seeing 
> proper levels in item 2 of simpleusb-tune-menu ? 5-6khz peaks?  If you 
> hit a DTMF key on the input radio can you hear the tone on the node 
> radio speaker?
>
> Baofeng radios can be a problem because if you don't mute the tones to 
> the speaker they are picked up both through a direct route and thru 
> the mic which often causes failure to decode.
>
> See this -
>
> https://www.kk6jyt.com/sending-accurate-baofeng-dtmf-tones-from-the-uv-5r/
>
> *73 Doug
> WA3DSP
> http://www.crompton.com/hamradio*
>
>
> > To: arm-allstar at hamvoip.org
> > Date: Sat, 20 Aug 2016 16:39:48 -0500
> > Subject: [arm-allstar] DTMF problem
> > From: arm-allstar at hamvoip.org
> > CC: wadeo at charter.net
> >
> > Good afternoon all,
> >
> > I am posting this here for a local ham friend. He just installing the
> > latest version of the Pi software on his Pi2. Everything went ok and
> > some small tweaks were made to work with his setup (i.e. - cleaning up
> > audio, cor, stuff like that). He also set up the ALLMON2 for his node
> > (27451). The issue he is running into is DTMF. When he uses RF to 
> access
> > his node the DTMF does nothing. Looking at the CLI it shows up as last
> > command heard, there was just no action was taken by asterisk. He can
> > make and break connections with both the CLI and Allmon just not over
> > the air. We have been all over it adjusting back and forth the pre- and
> > de- emphasis, pl filter on & off, making sure the function list was not
> > commented out for any reason..
> >
> > We have tried all we can think of. Any other suggestions we could have
> > over looked or should try?
> >
> > Thanks
> > Wade
> > KC0MLT
> >
> > _______________________________________________
> >
> > arm-allstar mailing list
> > arm-allstar at hamvoip.org
> > http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
> >
> > Visit the BBB and RPi2 web page - http://hamvoip.org
> >
>
>
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2 web page - http://hamvoip.org

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20160820/71d7cce9/attachment-0001.html>