[arm-allstar] FT-2900R COS Signal

[Joe]

Doug,
Does the URI COS pin 8 use + logic, so a high = USB and not USBINVERT? As for the buffer, I think the CMOS chips have a high fanout of 10 I think, so I shouldn’t need a buffer but I’ll certainly find out :-)
Thanks.

73
Joe - AD2DX




On Mar 28, 2015, at 2:41 AM, Doug Crompton <doug at crompton.com<mailto:doug at crompton.com>> wrote:

Joe,

 The URI cos input is blocked by a diode with a very weak pullup on the CM119 chip. So the high level could be any reasonable voltage up to 20-30 volts but it would usually never be that high. Usually around 12, 5V, or 3V depending on the radios logic level. It does not really matter as it is blocked by the diode. The thing that matters is that low is really low - zero volts or there about.

You probably would not have to buffer as the URI pin 8 has very little load. I guess experimentation is in order.

73 Doug
WA3DSP
http://www.crompton.com/hamradio


________________________________
From: joe at ad2dx.us<mailto:joe at ad2dx.us>
To: arm-allstar at hamvoip.org<mailto:arm-allstar at hamvoip.org>
Date: Sat, 28 Mar 2015 05:07:10 +0000
Subject: Re: [arm-allstar] FT-2900R COS Signal

Thanks Doug. I guess I need to understand COS a bit more. It appears that COS is a digital low or high (0V or +5V). I did find AF mute on a 16 pin DIP at pin12, so I guess I need to probe it with my logic probe while listening to squelch open and closed on a received signal.

I don't have a scope but I think my logic probe will give me enough info. I wonder if I have to buffer that signal if I try to use it as a COS line for the URI, if the URI loads that signal down too much, or if I can just take the signal right off that pin. I suspect no buffer would be needed.

Time to look at the URI schematic too...

Thanks.

Joe Lauricella, AD2DX
joe at AD2DX dot US
609-737-7064
________________________________
From: arm-allstar-bounces at hamvoip.org<mailto:arm-allstar-bounces at hamvoip.org> [arm-allstar-bounces at hamvoip.org<mailto:arm-allstar-bounces at hamvoip.org>] on behalf of Doug Crompton [doug at crompton.com<mailto:doug at crompton.com>]
Sent: Friday, March 27, 2015 11:20 PM
To: BeagleBone Black ARM Allstar
Subject: Re: [arm-allstar] FT-2900R COS Signal

Joe,

 Check out the service manual -

http://elektrotanya.com/yaesu_ft-2900r_sm.pdf/download.html

main unit schematic.  It looks like AF mute is a place to look. You will need to check levels with a signal. It is best to have a low (0 volt) signal on PL receive.


73 Doug
WA3DSP
http://www.crompton.com/hamradio


________________________________
From: joe at ad2dx.us<mailto:joe at ad2dx.us>
To: arm-allstar at hamvoip.org<mailto:arm-allstar at hamvoip.org>
Date: Fri, 27 Mar 2015 21:52:25 +0000
Subject: [arm-allstar] FT-2900R COS Signal

Hi Folks,
Does anyone know where I can find the COS signal inside the Yaesu FT-2900R? I can get TX/RX audio, PTT and ground from the outside of the unit but I poured through the schematics and cannot locate COS.
Thanks in advance.
73
Joe - AD2DX




This email communication and any files transmitted with it may contain confidential and or proprietary information and is provided for the use of the intended recipient only. Any review, retransmission or dissemination of this information by anyone other than the intended recipient is prohibited. If you receive this email in error, please contact the sender and delete this communication and any copies immediately. Thank you.
_______________________________________________ arm-allstar mailing list arm-allstar at hamvoip.org<mailto:arm-allstar at hamvoip.org> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
This email communication and any files transmitted with it may contain confidential and or proprietary information and is provided for the use of the intended recipient only. Any review, retransmission or dissemination of this information by anyone other than the intended recipient is prohibited. If you receive this email in error, please contact the sender and delete this communication and any copies immediately. Thank you.
_______________________________________________ arm-allstar mailing list arm-allstar at hamvoip.org<mailto:arm-allstar at hamvoip.org> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
_______________________________________________

arm-allstar mailing list
arm-allstar at hamvoip.org<mailto:arm-allstar at hamvoip.org>
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/

This email communication and any files transmitted with it may contain confidential and or proprietary information and is provided for the use of the intended recipient only. Any review, retransmission or dissemination of this information by anyone other than the intended recipient is prohibited. If you receive this email in error, please contact the sender and delete this communication and any copies immediately. Thank you.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20150328/4ab12351/attachment-0001.html>