[arm-allstar] BBB USB GPIO
petem001 at gmail.com
petem001 at gmail.com
Wed Jun 10 14:22:27 EST 2015
Frfom the source on the svn (version 951)
* status cmds:
*
* 1 - Force ID (global)
* 2 - Give Time of Day (global)
* 3 - Give software Version (global)
* 4 - Give GPS location info
* 11 - Force ID (local only)
* 12 - Give Time of Day (local only)
*
* cop (control operator) cmds:
*
* 1 - System warm boot
* 2 - System enable
* 3 - System disable
* 4 - Test Tone On/Off
* 5 - Dump System Variables on Console (debug)
* 6 - PTT (phone mode only)
* 7 - Time out timer enable
* 8 - Time out timer disable
* 9 - Autopatch enable
* 10 - Autopatch disable
* 11 - Link enable
* 12 - Link disable
* 13 - Query System State
* 14 - Change System State
* 15 - Scheduler Enable
* 16 - Scheduler Disable
* 17 - User functions (time, id, etc) enable
* 18 - User functions (time, id, etc) disable
* 19 - Select alternate hang timer
* 20 - Select standard hang timer
* 21 - Enable Parrot Mode
* 22 - Disable Parrot Mode
* 23 - Birdbath (Current Parrot Cleanup/Flush)
* 24 - Flush all telemetry
* 25 - Query last node un-keyed
* 26 - Query all nodes keyed/unkeyed
* 27 - Reset DAQ minimum on a pin
* 28 - Reset DAQ maximum on a pin
* 30 - Recall Memory Setting in Attached Xcvr
* 31 - Channel Selector for Parallel Programmed Xcvr
* 32 - Touchtone pad test: command + Digit string + # to playback all digits pressed
* 33 - Local Telemetry Output Enable
* 34 - Local Telemetry Output Disable
* 35 - Local Telemetry Output on Demand
* 36 - Foreign Link Local Output Path Enable
* 37 - Foreign Link Local Output Path Disable
* 38 - Foreign Link Local Output Path Follows Local Telemetry
* 39 - Foreign Link Local Output Path on Demand
* 40 - IRLP announce Enable
* 41 - IRLP announce Disable
* 42 - Echolink announce node # only
* 43 - Echolink announce node Callsign only
* 44 - Echolink announce node # & Callsign
* 45 - Link Activity timer enable
* 46 - Link Activity timer disable
* 47 - Reset "Link Config Changed" Flag
* 48 - Send Page Tone (Tone specs separated by parenthesis)
* 49 - Disable incoming connections (control state noice)
* 50 - Enable incoming connections (control state noicd)
* 51 - Enable sleep mode
* 52 - Disable sleep mode
* 53 - Wake up from sleep
* 54 - Go to sleep
* 55 - Parrot Once if parrot mode is disabled
* 56 - Rx CTCSS Enable
* 57 - Rx CTCSS Disable
* 58 - Tx CTCSS On Input only Enable
* 59 - Tx CTCSS On Input only Disable
* 60 - Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])
* Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call
* (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.
* DestID and subcode are only specified for the 'C' type message.
* UnitID is the local systems UnitID. DestID is the MDC1200 ID of
* the radio being called, and the subcodes are as follows:
* Subcode '8205' is Voice Selective Call for Spectra ('Call')
* Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or
* Astro-Saber('Call')
* Subcode '810D' is Call Alert (like Maxtrac 'CA')
*
*
* ilink cmds:
*
* 1 - Disconnect specified link
* 2 - Connect specified link -- monitor only
* 3 - Connect specified link -- tranceive
* 4 - Enter command mode on specified link
* 5 - System status
* 6 - Disconnect all links
* 11 - Disconnect a previously permanently connected link
* 12 - Permanently connect specified link -- monitor only
* 13 - Permanently connect specified link -- tranceive
* 15 - Full system status (all nodes)
* 16 - Reconnect links disconnected with "disconnect all links"
* 200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)
*
* remote cmds:
*
* 1 - Recall Memory MM (*000-*099) (Gets memory from rpt.conf)
* 2 - Set VFO MMMMM*KKK*O (Mhz digits, Khz digits, Offset)
* 3 - Set Rx PL Tone HHH*D*
* 4 - Set Tx PL Tone HHH*D* (Not currently implemented with DHE RBI-1)
* 5 - Link Status (long)
* 6 - Set operating mode M (FM, USB, LSB, AM, etc)
* 100 - RX PL off (Default)
* 101 - RX PL On
* 102 - TX PL Off (Default)
* 103 - TX PL On
* 104 - Low Power
* 105 - Med Power
* 106 - Hi Power
* 107 - Bump Down 20 Hz
* 108 - Bump Down 100 Hz
* 109 - Bump Down 500 Hz
* 110 - Bump Up 20 Hz
* 111 - Bump Up 100 Hz
* 112 - Bump Up 500 Hz
* 113 - Scan Down Slow
* 114 - Scan Down Medium
* 115 - Scan Down Fast
* 116 - Scan Up Slow
* 117 - Scan Up Medium
* 118 - Scan Up Fast
* 119 - Transmit allowing auto-tune
* 140 - Link Status (brief)
* 200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)
*
* playback cmds:
* specify the name of the file to be played globally (for example, 25=rpt/foo)
*
* localplay cmds:
* specify the name of the file to be played locally (for example, 25=rpt/foo)
*
* 'duplex' modes: (defaults to duplex=2)
*
* 0 - Only remote links key Tx and no main repeat audio.
* 1 - Everything other then main Rx keys Tx, no main repeat audio.
* 2 - Normal mode
* 3 - Normal except no main repeat audio.
* 4 - Normal except no main repeat audio during autopatch only
*
*/
From: Neil k8it
Sent: Wednesday, June 10, 2015 2:49 PM
To: ARM Allstar
Subject: Re: [arm-allstar] BBB USB GPIO
Does anyone have an up to date COP and ILINK command lists? After reviewing the fan control scripts I noticed the use of COP 62. The list I have only goes to COP58
Thanks
73 Neil Sablatzky K8IT
Allstar Node 41838 KITLINK
Allstar Node 42087 KITLINK HUB
IRLP Node exp0068
Echolink K8IT-L
--------------------------------------------------------------------------------
_______________________________________________
arm-allstar mailing list
arm-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
Visit the BBB web page - http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20150610/83ff4bef/attachment.html>
More information about the arm-allstar
mailing list