[arm-allstar] BBB node problems

Wed Jun 3 15:19:29 EST 2015

Hi Doug,

I have tried all combinations, I did the firstime.sh, in fact I did two
installs with no difference. However I tried a third install out of
desperation and it works. I don't know how or why but it does

Many thanks for your patience

Regards

Ken G0LCE

PS although others can connect to me and audio is good I still cannot use
the dtmf tones

I'm going to leave it for now and look at it when I'm not so tired

From: arm-allstar-bounces at hamvoip.org
[mailto:arm-allstar-bounces at hamvoip.org] On Behalf Of Doug Crompton
Sent: 03 June 2015 19:12
To: ARM Allstar
Subject: Re: [arm-allstar] BBB node problems

You are not getting the proper response. Below is what you should get.  I
don't think your tones are being decoded. Are you sure you have the
carrierfrom=  set right. If not things won't be working properly.

[Jun  3 14:02:03] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 1
[Jun  3 14:02:04] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 2
[Jun  3 14:02:04] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 3
[Jun  3 14:02:05] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 4
[Jun  3 14:02:06] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 5
[Jun  3 14:02:07] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 6
[Jun  3 14:02:07] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 7
[Jun  3 14:02:08] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 8
[Jun  3 14:02:09] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 9
[Jun  3 14:02:10] NOTICE[2237]: chan_simpleusb.c:2981 simpleusb_read: Got
DTMF char 0

This was done holding the PTT steady down and going through the keys.

There is not anything different in 1.2.1  that should make it not work. Your
going from usbradio to simpleusb is probably the biggest issue. You need to
get things setup correctly after switching.

73 Doug
WA3DSP
 <http://www.crompton.com/hamradio> http://www.crompton.com/hamradio

  _____  

From:  <mailto:ken at mirlaw.co.uk> ken at mirlaw.co.uk
To:  <mailto:arm-allstar at hamvoip.org> arm-allstar at hamvoip.org
Date: Wed, 3 Jun 2015 18:24:51 +0100
Subject: Re: [arm-allstar] BBB node problems

Hi Doug,

I can ping

64 bytes from ucsd.edu (132.239.180.101): icmp_seq=157 ttl=52 time=168 ms

Registry shows this

Host                  dnsmgr  Username    Perceived             Refresh
State

67.215.233.178:4569   Y       28468       151.227.213.230:1024       60
Registered

The results when I press the no 1 key on the radio comes back as

bbb-allstar*CLI>  -- Hungup 'DAHDI/pseudo-255737528'

No such command ' -- Hungup 'DAHDI/pseudo-255737528''

I typed simpleusb-tune-menu from the linux command and just tried it again
and it worked

I must have got it wrong 

I have had a node running for about four or five years from the acid setup
on my pc to running bbb vers 1 and running the raspberry pi 2 version to
without any problems. I need the raspberry for another project  which is why
I'm going back to the BBB and it's the first time I have had any problems

Tried various settings in simpleusb-tune-menu but no difference

Ken

From:  <mailto:arm-allstar-bounces at hamvoip.org>
arm-allstar-bounces at hamvoip.org [ <mailto:arm-allstar-bounces at hamvoip.org>
mailto:arm-allstar-bounces at hamvoip.org] On Behalf Of Doug Crompton
Sent: 03 June 2015 17:50
To: ARM Allstar
Subject: Re: [arm-allstar] BBB node problems

Ken,

 It looks like the ip address is correct.  See if you can ping at the linux
prompt -  ping ucsd.edu

Also go into the client - asterisk -rvvv   and  type  iax2 show registry

and see if you are registering.

The example you gave didn't show the actual tones in the display???  It
should print the DTMF key you press.

simpleusb-tune-menu is  a linux command - not in the client.

I don't recommend usbradio on any of the small boards at this time. I am
surprised you were using it on version 1.0

Do keep in mind that simpleusb requires a COS signal from the transceiver or
receiver indicating carrier. It also has to be set properly in
simpleusb.conf   -  carrierfrom=  usb  or usbinvert    -  usb if high on
signal and usbinvert if low (0v).  If this is not set properly it will not
work or work in weird ways.

carrierfrom   works with pin 8 on the DMK-URI.   Pin 8 should go to the rigs
cos output.

This is all in the setup docs at hamvoip.org  - did you read them?

73 Doug
WA3DSP
 <http://www.crompton.com/hamradio> http://www.crompton.com/hamradio

  _____  

_______________________________________________ arm-allstar mailing list
<mailto:arm-allstar at hamvoip.org> arm-allstar at hamvoip.org
<http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar>
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar Visit the BBB
web page -  <http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/>
http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20150603/3a74e4a1/attachment-0001.html>