[arm-allstar] New HAM need help with DTMF

Sam Bonsett bonsett at gmail.com
Mon Jul 27 15:17:45 EST 2015 

OkI got it working.  Thanks!

But now I hear a short tone after each transmission made by the other
station.
What is the command to re create my call sign voice id ?  I hear wa3xyz
pl88.5 which I believe is the sample.



On Mon, Jul 27, 2015 at 4:00 PM, Kenneth Grimard <n1dot1 at gmail.com> wrote:

> hi david
>
> here is the thing jim duude would have turned that off in the acid source
> tree
> if he felt it was a problem. i would rather have a radio dtmf work then
> not work.
>
> some radio WILL NOT work even if you have the level correct because of
> this.
>
> ken n1dot
>
>
>
>
> On 7/27/2015 7:51 PM, David McGough wrote:
>
>> Hi Ken,
>>
>> I, personally, haven't encounted any cheap HT's where DTMF failed to
>> decode with radio relax off--at least if they'd decode at all on any
>> system! Almost every case I've seen where DTMF didn't decode could be
>> corrected by careful audio level adjustment at the channel driver end.
>>
>> The problem with leaving radio relax enabled is that there will be very,
>> very many false decodes and the cooresponding 20ms audio chop. That gets
>> really annoying (to me, at least).
>>
>> 73, David KB4FXC
>>
>>
>>
>>
>> On Mon, 27 Jul 2015, Kenneth Grimard wrote:
>>
>>  the reason why i had asked is this. with some of the chinese
>>> radio's the dtmf encoder has a very bad problem with excessive twist.
>>>
>>> i know the reason why they try to eliminate the false decoding
>>> but with it off it will cause quite a few radio's to not be able to
>>> use the dtmf due to the bad twist between the tones.
>>>
>>> I have wouxun that has this problem. this will also
>>> cause problems with certain yaesu radio's too.
>>>
>>> i tried on my desktop with it off and it gave me a real problem
>>> with it off. a lot of my radio's the dtmf would not work until i turned
>>> it
>>> back on and re-complied the source code.
>>>
>>> I may have to do the same with the bbb or the rpi2 images then.
>>> i would rather have a little of false decoding then have some of may
>>> radio's
>>> dtmf pad not work due to bad twist levels.
>>>
>>> ken n1dot
>>>
>>>
>>>
>>>
>>> On 7/27/2015 7:36 PM, David McGough wrote:
>>>
>>>> Yes, radio relax is off (not checked in the menu setup).
>>>>
>>>> On Mon, 27 Jul 2015, Kenneth Grimard wrote:
>>>>
>>>>  Hi all
>>>>>
>>>>> I did have a question about the rpi and bbb images.
>>>>> it radio relax turned off in the source code in these images?
>>>>>
>>>>> ken n1dot
>>>>>
>>>>>
>>>>>
>>>>> On 7/27/2015 6:35 PM, Jon Rorke wrote:
>>>>>
>>>>>> this line should read: Also maybe set rx boost =1 (yes). if the rx
>>>>>> audio is too low then tones wont decode.
>>>>>> Jon
>>>>>>
>>>>>> On 7/27/2015 2:23 PM, Jon Rorke wrote:
>>>>>>
>>>>>>> Check to see if the node is seeing the cor from your radio. If not
>>>>>>> then it will not read DTMF.
>>>>>>>
>>>>>>> Also maybe set rx boot =1 (yes). if the rx audio is too low then
>>>>>>> tones wont decode.
>>>>>>>
>>>>>>> On 7/27/2015 2:09 PM, Sam Bonsett wrote:
>>>>>>>
>>>>>>>> Ok I bumped it up to 650 and it works on my Baofeng but does not
>>>>>>>> work with my Yaesu FT-60. (might be low battery?)
>>>>>>>>
>>>>>>>> Will set the duplex to 1
>>>>>>>>
>>>>>>>> Thanks Doug!
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> On Mon, Jul 27, 2015 at 1:46 PM, Sam Bonsett <bonsett at gmail.com
>>>>>>>> <mailto:bonsett at gmail.com>> wrote:
>>>>>>>>
>>>>>>>>       yes that works but that is how I have been connecting to
>>>>>>>>       nodes...  Actually I use this:
>>>>>>>>       rpt cmd 42197 ilink 3 42181
>>>>>>>>
>>>>>>>>       What I want to do is connect to a node from my HT.
>>>>>>>>
>>>>>>>>       on HT *342181 should connect me to node 42181 but it does not.
>>>>>>>>
>>>>>>>>       Sam
>>>>>>>>       km4ksr
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>       On Mon, Jul 27, 2015 at 1:35 PM, Robert Newberry
>>>>>>>>       <N1XBM at amsat.org> wrote:
>>>>>>>>
>>>>>>>>           Try this.
>>>>>>>>
>>>>>>>>           Log into your box.
>>>>>>>>
>>>>>>>>           Type asterisk -r
>>>>>>>>           Then once in CLI type rpt fun (your node number) *342181
>>>>>>>>
>>>>>>>>           Where I put parentheses please supply your nodes number
>>>>>>>>           without parentheses.
>>>>>>>>
>>>>>>>>           Tell us if that works!
>>>>>>>>
>>>>>>>>           N1XBM
>>>>>>>>           Apparare Scientor
>>>>>>>>           Paratus Communicare
>>>>>>>>           Allstar Node # 27086, 41540, 41812
>>>>>>>>
>>>>>>>>
>>>>>>>>           _______________________________________________
>>>>>>>>
>>>>>>>>           arm-allstar mailing list
>>>>>>>>           arm-allstar at hamvoip.org <mailto:arm-allstar at hamvoip.org>
>>>>>>>>
>>>>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>>>>>
>>>>>>>>           Visit the BBB and RPi2 web page - http://hamvoip.org
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> _______________________________________________
>>>>>>>>
>>>>>>>> arm-allstar mailing list
>>>>>>>> arm-allstar at hamvoip.org
>>>>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>>>>>
>>>>>>>> Visit the BBB and RPi2 web page -http://hamvoip.org
>>>>>>>>
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>>
>>>>>>> arm-allstar mailing list
>>>>>>> arm-allstar at hamvoip.org
>>>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>>>>
>>>>>>> Visit the BBB and RPi2 web page -http://hamvoip.org
>>>>>>>
>>>>>>
>>>>>> _______________________________________________
>>>>>>
>>>>>> arm-allstar mailing list
>>>>>> arm-allstar at hamvoip.org
>>>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>>>
>>>>>> Visit the BBB and RPi2 web page - http://hamvoip.org
>>>>>>
>>>>> _______________________________________________
>>>>
>>>> arm-allstar mailing list
>>>> arm-allstar at hamvoip.org
>>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>>
>>>> Visit the BBB and RPi2 web page - http://hamvoip.org
>>>>
>>> _______________________________________________
>>>
>>> arm-allstar mailing list
>>> arm-allstar at hamvoip.org
>>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>>
>>> Visit the BBB and RPi2 web page - http://hamvoip.org
>>>
>>>  _______________________________________________
>>
>> arm-allstar mailing list
>> arm-allstar at hamvoip.org
>> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>>
>> Visit the BBB and RPi2 web page - http://hamvoip.org
>>
>
> _______________________________________________
>
> arm-allstar mailing list
> arm-allstar at hamvoip.org
> http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar
>
> Visit the BBB and RPi2 web page - http://hamvoip.org
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20150727/4f8b007c/attachment.html>

More information about the arm-allstar mailing list