[arm-allstar] [Doug?] USB Pointing problem- More info?

Fri Aug 28 20:02:52 EST 2015

All the setup info is in the setup document in the how-to section at hamvoip.org. Below is a direct link to that document. The second node procedure is at the end. You will have to back yourself up to one node - Physically remove the second node, then comment out the second node radio=  - return it to pseudo then reboot.   Then follow the directions in the pdf exactly. Don't connect until told and once they are setup mark the physical location where they are plugged in and don't move them.
http://www.crompton.com/hamradio/BeagleBoneBlackAllstar/config-setup.pdf

73 Doug
WA3DSP
http://www.crompton.com/hamradio

Date: Sat, 29 Aug 2015 00:34:36 +0000
From: kd8usf at yahoo.com
To: doug at crompton.com
Subject: Re: Fwd: [arm-allstar] [Doug?] USB Pointing problem- More info?

Doug,I did not. I added the second node  later on. Where can I find those instructions?
Thanks.Andrew. 
        From: kk6ecm <kk6ecm at gmail.com>
 To: "kd8usf at yahoo.com" <kd8usf at yahoo.com> 
 Sent: Friday, August 28, 2015 7:55 PM
 Subject: Fwd: [arm-allstar] [Doug?] USB Pointing problem- More info?

Don't know if you've joined this list, so forwarding

Thanks,Bobkk6ecm
Sent from iPad

Begin forwarded message:

From: Doug Crompton <doug at crompton.com>
Date: August 28, 2015 at 3:26:32 PM PDT
To: ARM Allstar <arm-allstar at hamvoip.org>
Subject: Re: [arm-allstar] [Doug?] USB Pointing problem- More info?
Reply-To: ARM Allstar <arm-allstar at hamvoip.org>

Did you install the twp node system initially as per the instructions?
73 Doug
WA3DSP
http://www.crompton.com/hamradio

From: kk6ecm at gmail.com
Date: Fri, 28 Aug 2015 13:49:08 -0700
To: kd8usf at yahoo.com
CC: arm-allstar at hamvoip.org
Subject: Re: [arm-allstar] [Doug?] USB Pointing problem- More info?

Seems the two systems are different... What works for ACID may not work for the BBB/RPi setup. I'm moving this over to ARM Allstarlink list.

Thanks,Bobkk6ecm
Sent from iPad

On Aug 28, 2015, at 1:27 PM, KD8USF <kd8usf at yahoo.com> wrote:

That brings up some questions I have about this- I have 2 interfaces on the Pi2 running Dougs image, sometimes when I reboot it, the two nodes both try to use the same interface even though they are configured in the tune files. Throws up errors in a continuous loop. When I restart asterisks from the command line it then works as it should and the two nodes are using their assigned interfaces. It's almost like the two interfaces are not fully initialized before asterisk starts on bootup. Now this is what lsusb shows:
Bus 001 Device 005: ID 0d8c:000c C-Media Electronics, Inc. Audio AdapterBus 001 Device 004: ID 0d8c:000c C-Media Electronics, Inc. Audio Adapter
When I used the tune menu to set the levels it wrote in the devices as follows:
For node 42051: devstr=1-1.4:1.0

For node 42078: devstr=1-1.5:1.0
Should I change that to 1-4 for node 42051, and 1-5 for node 42078? Andrew.

        From: kk6ecm <kk6ecm at gmail.com>
 To: chris <ckw at gci.net> 
Cc: "App_rpt-users at ohnosec.org" <App_rpt-users at ohnosec.org> 
 Sent: Wednesday, August 26, 2015 10:23 PM
 Subject: Re: [App_rpt-users] Allstar

You may have a USB pointing problem between asterisk and Linux.On boot up type "service asterisk stop" at the command promptType lsusb at the command prompt. [root at Xxxxxx~]# lsusbBus 004 Device 004: ID 0d8c:013c C-Media Electronics, Inc. CM108 Audio ControllerBus 004 Device 001: ID 0000:0000  Bus 004 Device 002: ID 0d8c:013c C-Media Electronics, Inc. CM108 Audio ControllerBus 001 Device 001: ID 0000:0000  Bus 003 Device 001: ID 0000:0000  Bus 002 Device 001: ID 0000:0000  Bus 005 Device 001: ID 0000:0000  Then make sure your tune files ( in /etc/asterisk) properly point to your USB device such as a URI in devstr=  (see below example)[root at xxxxx asterisk]# cat usbradio_tune_usb<node#>.conf[usb27178]; name=usb<node#>; devicenum=1devstr=4-2    ; Bus 004 Device 002: ID 0d8c:013c C-Media Electronics, Inc. CM108 Audio Controllerrxmixerset=125txmixaset=500txmixbset=500rxvoiceadj=1.820479rxctcssadj=0.500000txctcssadj=0rxsquelchadj=825Correct the tune file thenAt the command prompt type: service asterisk startThanks,Bobkk6ecmSent from iPad> On Aug 26, 2015, at 5:48 PM, chris <ckw at gci.net> wrote:> > Hello Again. I failed to mention The Allstar server is running ACID. After boot up It repeats the following ,> (asterisk) did not claim interface 3 before use. Forgot where to fix this. Thanks again. > > Chris> Allstar node 42264 > _______________________________________________> App_rpt-users mailing list> App_rpt-users at ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users> > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. 

_______________________________________________App_rpt-users mailing listApp_rpt-users at ohnosec.orghttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-usersTo unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. 

_______________________________________________

arm-allstar mailing list
arm-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2 web page - http://hamvoip.org 		 	   		  
_______________________________________________

arm-allstar mailing list
arm-allstar at hamvoip.org
http://lists.hamvoip.org/cgi-bin/mailman/listinfo/arm-allstar

Visit the BBB and RPi2 web page - http://hamvoip.org

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.hamvoip.org/pipermail/arm-allstar/attachments/20150828/eabf443e/attachment.html>